Download the Danalock App Go to Google Play or App Store and download the Danalock App. When the App has been installed, create a user profile and sign in. You will use this profile each time you sign into the App.
LED-Signals LED signal LED color Status indication Long white blink Power on. Batteries are activated Constant red while performing Device is locking Constant green while performing Device is unlocking Red blink every 5 minutes Device battery level is critically low Constant purple light Device is ready to update Blue while performing action...
Page 18
When you get to the setting you want to change, wait for 5 seconds and the Danalock will react to your command. If you make a wrong number of clicks, just stop at a number of clicks where the LED doesn’t light up and wait for 5 seconds.
Page 19
Green Inclusion mode This mode is used to in- or exclude your Danalock with a Z-Wave or Zigbee gateway. When the Danalock blinks green it is in ex/inclusion mode and you have 30 seconds to pair the Danalock with a gateway.
Page 20
Specifi c Human Absorption Ratio (SAR) corrosion resistance classifi cation grade=0. (such a The Danalock V3 unit is not intended for handheld use or to be 4 Do not worn on the body. A minimum separation of eight (8”) inches Accessories and Batteries 5 Do not...
Page 21
The Danalock cannot be turned off after installation, so any It is very important to replace all 4 batteries at the same time. building installed with Danalock etc. must not be located in an Please use only standard CR123 lithium batteries. Not replacing...
Page 22
“ Not applicable”). commercial waste. specifi catio Warranty Danalock ApS products are covered by a limited manufacturer Material warranty. The Danalock ApS warranty is limited to the warranty Radio inter rules and legislation present in each country. The warranty (A-C/F-H/L/W (1-9) (0/A-F)
Page 23
NOTICE statements according to CFR 47 Part 15.21: ments Changes or modifi cations made to this equipment not expressly ct to the approved by Danalock Aps may void the FCC authorization to Product specifi cations e and operate this equipment.
Page 24
Danalock Regulatory labeling The Danalock V3 BT product are regulatory compliant to the following regulation (Europe, USA/Canada, Japan, Australia/NZ): Product sp Supply Volt REACH RoHS COMPLIANT Temperatu 2011/65/EU Amendment range 2015/863/EU Mechanical specifi catio FCC ID: 2ADSH-V3BT 202-SMF017 IC:12588A-V3BT Material...
Page 25
Danalock V3 BTZBE / Danalock V3 BTZB NOTICE statements according to CFR 47 Part 15.21: Changes or modifi cations made to this equipment not expressly approved by Danalock Aps may void the FCC authorization to Product specifi cations operate this equipment.
Page 26
Temperatu Amendment 2015/863/EU range Mechanical FCC ID: 2ADSH-V3BTZBE 204-920100 specifi catio IC:12588A-V3BTZBE Material For the Danalock V3 BTZB version the following label diff erences Radio inter are applicable: FCC ID: 2ADSH-V3BTZB 202-SMF018 IC:12588A-V3BTZB United Ara The product number ER7 Regulatory...
Page 27
United Arab Emirates (UAE) certifi cation. The product has been approved by UAE TRA with registration number ER75325/19 and the dealer number: DA83047/1 Regulatory labeling: The Danalock V3-BTZE product are regulatory compliant to the following regulation (Europe, UAE(Dubai)): REACH RoHS...
Page 28
4x3V DC (12V DC) Supply Volt Declarations Standby time on 450 Days Certifi cates and Suppliers Declaration of Conformity (SDOC) battery statements can be downloaded from the danalock website: Temperature Active operating mode -10ºC to +40ºC Temperatu https://danalock.com/legal/certifi cates/ range...
Page 29
NOTICE statements according to CFR 47 Part 15.21: Changes or modifi cations made to this equipment not expressly が無効 approved by Danalock Aps may void the FCC authorization to Product specifi cations operate this equipment. Supply Voltage Via USB 4x3V DC (12V DC) Statements according to CFR 47 Part 2.1091 and OET...