Table of Contents
Advertisement
Quick Links
Operation Manual
Demolition Hammer
61202
Illustration similar, may vary depending on model
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps and technical data can differ insignific -
antly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities, please contact us.
Advertisement
Table of Contents
Related Manuals for WilTec 61202
Summary of Contents for WilTec 61202
- Page 1 Operation Manual Demolition Hammer 61202 Illustration similar, may vary depending on model Read and follow the operating instructions and safety information before using for the first time. Technical changes reserved! Due to further developments, illustrations, functioning steps and technical data can differ insignific - antly.
- Page 2 All rights reserved. The WilTec Wildanger Technik GmbH cannot be held accountable for any possible mistakes in this operating manual, nor in the diagrams and figures shown.
-
Page 3: Safety Instructions
Do not touch the drill immediately after it has run. The drill will be hot and may cause burns. Always check that the bits are firmly placed before starting the device up. © by WilTec Wildanger Technik GmbH Artikel 61202 Seite 3 http://www.WilTec.de... - Page 4 Do not use the device if it does not work correctly or has been damaged by a fall. Do not di- sassemble the device yourself but contact your a qualified technician. © by WilTec Wildanger Technik GmbH Artikel 61202 Seite 4 http://www.WilTec.de...
-
Page 5: Technical Data
Transport box Chisel (overall length 410 mm) 1x Oil supply Hex wrench Socket wrench Application: Demolition, crushing and chipping of concrete/ brickwork © by WilTec Wildanger Technik GmbH Artikel 61202 Seite 5 http://www.WilTec.de http://www.aoyue.eu 2020-1 http://www.teichtip.de... - Page 6 Oil level indicator, check the oil quantity by holding the drill vertically Fill up with oil if the quantity falls below 3 mm Wear limit Carbon brush number Standard carbon brush Auto stop of the carbon brush © by WilTec Wildanger Technik GmbH Artikel 61202 Seite 6 http://www.WilTec.de http://www.aoyue.eu 2020-1...
-
Page 7: Before Use
Therefore, grease the shank end of the tool regularly with gear grease before inserting it. Wait until the shank has cooled down after operating the tool. Otherwise there is a danger of being burnt! © by WilTec Wildanger Technik GmbH Artikel 61202 Seite 7 http://www.WilTec.de... -
Page 8: Maintenance And Servicing
The "heart" of the device is the electric motor. Always make sure that the electric mo- tor is never damaged and/ or gets wet with oil or water. © by WilTec Wildanger Technik GmbH Artikel 61202 Seite 8 http://www.WilTec.de http://www.aoyue.eu... - Page 9 If any further maintenance or repair work requires the housing to be opened, only have it carried out by a qualified specialist or contact an authorized service partner. © by WilTec Wildanger Technik GmbH Artikel 61202 Seite 9 http://www.WilTec.de http://www.aoyue.eu...
-
Page 10: Disposal Regulations
All WilTec electric devices that fall under the WEEE regulations are labelled with the crossed-out wheeled waste bin logo. This logo indicates that this electric equipment must not be disposed with the domestic waste. -
Page 11: Eg-Konformitätserklärung
Firma / Company / Société WilTec Wildanger Technik GmbH Koenigsbenden 12 52249 Eschweiler, Deutschland erklärt, dass das Produkt: Abbruchhammer 61202 / / PH65B, PH65H, PH65A, 65, 75A, 80, Type: 85, 85B, 90, 95, 0810, 11E Verwendungszweck: Abbrucharbeiten / Sanierungen mit den folgenden EG-Rats-Richtlinien übereinstimmt: This appliance is in conformity with the following european directives: Cet appareil est conform aux dierectives européennes:...