Table of Contents
Advertisement
Quick Links
R8-17...R20-17
Model: EVO 20 R, EVO 20 R BT
Assembly and Operating Instructions
en
Tubular drive with variable output speeds for roller
shutter systems and vertical fabric shades.
Important information for:
• Fitters / • Electricians / • Users
Please forward accordingly!
These instructions must be kept safe for future reference.
1010 300 002 0g 16/03/2021
Becker-Antriebe GmbH
Friedrich-Ebert-Straße 2-4
35764 Sinn/Germany
www.becker-antriebe.com
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Becker EVO 20 R
Summary of Contents for Becker EVO 20 R
- Page 1 R8-17...R20-17 Model: EVO 20 R, EVO 20 R BT Assembly and Operating Instructions Tubular drive with variable output speeds for roller shutter systems and vertical fabric shades. Important information for: • Fitters / • Electricians / • Users Please forward accordingly! These instructions must be kept safe for future reference.
-
Page 2: Table Of Contents
Table of contents General .................................... 3 Warranty ..................................... 3 Safety instructions ................................ 4 Instructions for the user.............................. 4 Instructions for installation and commissioning........................ 4 Intended use .................................. 6 Assembling and disassembling the plug-in connecting cable.................... 6 Installation................................... 7 Assembling the drive ............................... 7 Undoing the mounting pin.............................. -
Page 3: General
General These tubular drives are high-quality products with the following features: • Optimised for roller shutter operation and vertical fabric shades • Different driving profiles • Installation without stops possible (from lower point to upper point) • Automatic detection of limit positions thanks to intelligent electronic system with stop systems •... -
Page 4: Safety Instructions
Safety instructions The following safety instructions and warnings are intended to avert hazards and to prevent property damage and personal injury. Instructions for the user General information • The drive must be disconnected from its power source during cleaning and maintenance and when re- placing parts. - Page 5 • Hazardous moving parts of the drive must be installed at a height of over 2.5 m above floor level or any other surface from which the drive can be accessed. • To ensure safe operation of the system after commissioning, the limit positions must be correctly set/ programmed in.
-
Page 6: Intended Use
Intended use The type of tubular drive described in these instructions is intended solely for the operation of roller shutter systems and vertical fabric shades. This type of tubular drive supports not only curtain attachment by means of springs but also rigid shaft connectors, such as mech- anical anti-lifting devices manufactured by Zurfluh-Feller, Simu, GAH Alberts and Deprat. -
Page 7: Installation
Installation Assembling the drive Attention To connect the drive to the driven part, solely mechanical accessory components made by the drive manufacturer from the current product catalogue may be used. Prior to mounting, the fitter must ensure that the masonry and the system being motorised are sufficiently robust (drive torque plus weight of the shading solution). -
Page 8: Disassembling The Drive Adapter With Safety Catch On The Drive Shaft
Disassembling the drive adapter with safety catch on the drive shaft Disassembly with disassembly tool, Item no. 4930 300 606 0 Disassembly with long nose pliers Mounting the drive in the tube For profile tubes: In the case of some drive adapters, tolerances of the groove widths in different bar- rels can be offset by rotating the drive adapter into a different groove recess. - Page 9 Attention Do not hammer the tubular drive into the tube or drop it into the barrel! The curtain can only be secured using springs or rigid shaft connectors. We recommend at least three pieces per metre of barrel. Assemble the tubular drive with the relevant ring (1) and drive adapter (2). If the ring has several grooves, select the groove which is a perfect fit and push the ring (1) onto the thrust ring.
-
Page 10: Setting The Limit Positions Using The Programming Unit
Setting the limit positions using the programming unit Programming unit for drives with electronic limit switching. Programming button Travel button Attention The programming unit is only designed for the commissioning, and not for continuous op- eration. Intelligent installation management Completion of installation following automatic setting of limit position "Stop" The drive saves the limit position "Stop"... - Page 11 Upper point to lower point There is no shading solution length adjustment with this limit position setting. Open to the desired upper limit position. Press the programming button of the programming unit for 3 seconds. ▻ The tubular drive acknowledges. Then close to the desired lower limit position.
-
Page 12: Deleting The Limit Positions Using The Programming Unit
Deleting the limit positions using the programming unit Connect the wires of the tubular drive to those of the same colour in the programming unit and switch on the power supply. Please pause for 1 sec after the last drive command before beginning the deletion se- quence. -
Page 13: Adjusting The Limit Positions With A Rotary Switch Or A Locking Button
Deleting both limit positions Any additional functions that may have been set are deleted at the same time, or are reset to the factory default settings. Open/close the shading solution to a point between the limit positions. Press the programming button and keep it pressed. Then press down the travel button and keep it pressed. - Page 14 Upper stop to lower stop This option for setting the limit positions is not possible with a vertical fabric shade. Open to the permanent upper stop. ▻ The tubular drive switches off automatically. Then close to the permanent lower stop without pausing. During travel, the limit posi- tion status indicator (LSI) must be displayed before the limit position is reached.
-
Page 15: Deleting The Limit Positions With A Rotary Switch Or A Locking Button
Upper point to lower stop This option for setting the limit positions is not possible with a vertical fabric shade. Open to the desired upper limit position. Carry out the following sequence without interruption between the individual drive commands. ▻ The tubular drive confirms. until STOP and hold until Then close to the permanent lower stop. -
Page 16: Activating Bluetooth
The operator unit must have at least Bluetooth version 4.0. You can find this information in the operating instructions for the operator unit. Download the Becker Service app from Google Play Store or the App-Store, and install it on the operator unit. ® Activating Bluetooth on the tubular drive ®... -
Page 17: Modifying The Zone For Slow Travel
Modifying the zone for slow travel In the “Standard operation” travel profile, the length of the zone for slow travel on the shading solution can be modified. This function is available from the date of manufacture 1842 (see “General” section). The limit positions must be fixed and the tubular drive must be in the “Standard operation”... -
Page 18: Obstacle Detection
Activating/deactivating the upper anti-freeze mechanism Open/close the shading solution to a point between the limit positions. Press the programming button on the programming unit (for approx 10 s) until the tu- bular drive confirms. Obstacle detection Caution Please note that the drive must be pushed into the shaft as far as the band of the thrust ring. -
Page 19: Information For The Electrician
These drives are maintenance-free. Technical data dia. 45 Tubular drive R8-17 R12-17 R20-17 Model EVO 20 R, EVO 20 R BT Type C EVO ROP+, C EVO ROP+ BT Rated torque [Nm] Output speed [rpm] Limit switch range 64 revolutions Supply voltage 230 V AC / 50 Hz... -
Page 20: What To Do If
What to do if...? Problem Remedy The roller shutter curtain is raised unevenly or not at all. Stops have broken off or one or several attachments are broken. Repair system; delete limit positions, then reprogram limit positions. Tubular drive overruns the limit position or does not reach the Repair system;... -
Page 21: Sample Wiring Diagrams
Sample wiring diagrams The assignment of the black and brown wires according to the direction of travel is de- pendant on how the drive is installed (mounted to the right or to the left). Controlling one/several drive(s) via a single switch/button 21 - en... - Page 22 Central, group and individual control using Centronic UnitControl UC42 Central Control unit Mains 230 V / 50 Hz Central cable 230 V / 50 Hz (connection to further control units) Group 230 V / 50 Hz Individual Individual 230 V / 50 Hz 230 V / 50 Hz 22 - en...
-
Page 23: Declaration Of Conformity
Declaration of conformity 23 - en... - Page 24 Declaration of conformity 24 - en...
-
Page 25: Licensing Information For Open Source Software
Written request for the licence texts: Becker-Antriebe will, on request, provide the licence texts for the licensed software being used at cost price, either on a USB stick or a similar data carrier. Please send an email to the following email address for more information: licenses@becker‑antriebe.com Licenses Apache 2.0... - Page 26 Copyright (c) 1989, 1993 The Regents of the University of California. This code is derived from software contributed to Berkeley by Guido van Rossum. Copyright (c) 1992 Henry Spencer. Copyright (c) 1992, 1993 The Regents of the University of California. All rights reserved. This code is derived from software con- tributed to Berkeley by Henry Spencer of the University of Toronto.
- Page 27 Permission to use, copy, modify, and distribute this software for any purpose without fee is hereby granted, provided that this en- tire notice is included in all copies of any software which is or includes a copy or modification of this software and in all copies of the supporting documentation for such software.
Need help?
Do you have a question about the EVO 20 R and is the answer not in the manual?
Questions and answers