Table of Contents
Advertisement
Quick Links
ACE10 Variable Frequency Drive System
Installation & Maintenance Information
Designated space for
additional DIN rail mountable
terminals/relays
Blower
cooling intake
Data nameplate
including torque
information
Control pad
assembly
External
ground
TABLE OF CONTENTS
1.
2.
3.
4.
IF 1619 • 05/18
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
Shrouds
Manifold
Blower
Blower
fuse
block
(not
shown)
Disconnect
VFD
switch
Internal
ground
Page 2
Page 2
Page 2
Page 2
Page 2
Page 3
Page 4
Page 4
Page 5
Page 6
Page 6
Page 6
Page 6
Page 6
Page 6
Page 6
Page 7
Page 8
Page 8
Page 8
Copyright
Warning plate
Control pad
Baffle
viewing
window
Explosionproof
filter
(pre-filters
removed for
clarity)
5.
6.
7.
8.
2018, Eaton's Crouse-Hinds Division
©
IF 1619
Shroud
Product
nameplate
with critical
markings
Indicating
lights
Control pad
button
assembly
Disconnect
operating
handle
Warning plate
Page 9
Page 9
Page 9
Page 9
Page 9
Page 10
Page 10
Page 10
Page 10
Page 10
Page 10
Page 11
Page 11
Page 11
Page 11
Page 12
Page 12
Page 1
Advertisement
Table of Contents
Related Manuals for Eaton CROUSE-HINDS ACE10 Series
Summary of Contents for Eaton CROUSE-HINDS ACE10 Series
-
Page 1: Table Of Contents
8.3.1 Blower installation instructions Page 11 4.1 Keypad interface Page 8 4.2 Disconnect and lockout/tagout Page 8 8.4 Pushbutton operator kit Page 12 8.4.1 Pushbutton installation instructions Page 12 IF 1619 • 05/18 Copyright 2018, Eaton’s Crouse-Hinds Division Page 1 ©... -
Page 2: Safety Instructions
WARNING To avoid cooling system malfunction and personnel injury, be sure to torque the first eight (8) cover screws sequentially per Figure 1 before torquing the remaining screws. IF 1619 • 05/18 Copyright © 2018, Eaton’s Crouse-Hinds Division Page 2... -
Page 3: Mechanical Installation
"X" It is imperative that the enclosure be well ventilated to ensure reliable performance. Adequate space around the intake and exhaust of the enclosure MUST be accommodated. Eaton’s Crouse-Hinds Division recommends ‘x’ be a minimum of 12 inches (0.3 meters). -
Page 4: Weights
Use the dedicated lifting eye to mount enclosure on suitable mounting surface. Select a mounting location that will provide suitable strength and rigidity for supporting the enclosure and all components. IF 1619 • 05/18 Copyright © 2018, Eaton’s Crouse-Hinds Division Page 4... -
Page 5: Dimensional Drawings
2.4 DIMENSIONAL DRAWINGS IF 1619 • 05/18 Copyright © 2018, Eaton’s Crouse-Hinds Division Page 5... -
Page 6: Mounting
Attach motor cable shielding to VFD ground (see recommendations by drive manufacturer). Remove terminal knockouts and reinstall VFD terminal shroud. Refer to the drive manufacturer’s manual for further information regarding drive installation. IF 1619 • 05/18 Copyright 2018, Eaton’s Crouse-Hinds Division Page 6 ©... -
Page 7: Control Wire Routing
To avoid the transmission of noise to/from the blower and/or the variable frequency drive load conductors, be sure to bundle all field control wiring and shield as necessary. 3.5 BLOWER AND SIGNAL SCHEMATIC IF 1619 • 05/18 Copyright © 2018, Eaton’s Crouse-Hinds Division Page 7... -
Page 8: Communication Modules
Criteria is identified in the lower corners of the control pad corresponding to the buttons (as shown). Refer to the drive manufacturer’s manual for additional instruction on the proper use and capability of the keypad interface. IF 1619 • 05/18 Copyright © 2018, Eaton’s Crouse-Hinds Division Page 8... -
Page 9: Maintenance
Inspect all other components and verify that they are in proper operating condition. Consult Eaton’s Crouse-Hinds Division for replacement parts as needed. WARNING: BURN HAZARD To avoid personnel injury, allow sufficient time for the enclosure to cool prior to servicing. -
Page 10: Technical Data
ACE systems are designed to provide years of reliable service. However, should de-rating is 1% for every 100m (328 ft.). the need for replacement parts arise, they are available through your Eaton’s NOTE: If the installation site is higher than 2,000m (6,560 ft.) above sea level, Crouse-Hinds Division Distributor. -
Page 11: Sintered Filter Kit
20. Terminate the blower ground wire to the appropriate terminal block (with the blower control wires) (yellow/green to green) 21. Perform a continuity check between the ground terminal and the ground lug adjacent to the integral disconnect switch. IF 1619 • 05/18 Copyright © 2018, Eaton’s Crouse-Hinds Division Page 11... -
Page 12: Pushbutton Operator Kit
All statements, technical information and recommendations contained herein are based on information and tests we believe to be reliable. The accuracy or completeness thereof are not guaranteed. In accordance with Eaton’s Crouse-Hinds Division’s “Terms and Conditions of Sale,” and since conditions of use are outside our control, the purchaser should determine the suitability of the product for his intended use and assumes all risk and liability whatsoever in connection therewith.
Need help?
Do you have a question about the CROUSE-HINDS ACE10 Series and is the answer not in the manual?
Questions and answers