Eaton Crouse-Hinds Series Installation & Maintenance Information
Variable frequency drive system
Hide thumbs
Also See for Crouse-Hinds Series:
- Instruction manual (114 pages) ,
- Operating instructions manual (44 pages) ,
- Technical manual (32 pages)
Table of Contents
Advertisement
Quick Links
ACE-DG1 Variable Frequency Drive System
Installation & Maintenance Information
Blower Cooling
Data Nameplate,
Intake
including Torque
Information
External
Internal
Ground
Ground
TABLE OF CONTENTS
IF 1767 • 09/15
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
Manifold
Blower
Disconnect
Switch
Page 2
Page 2
Page 2
Page 2
Page 2, 3
Page 3
Page 3
Page 3
Page 4
Page 5
Page 5
Page 5
Page 5,
Page 5, 6
Page 5, 6
Page 5, 6
Page 7
Page 7
Page 7
Page 8
Page 8
Page 8
Copyright
2015, Eaton's Crouse-Hinds Division
©
Explosionproof
Filter
(pre-filters
removed for clarity)
5.3 Torque Verification
6. Technical Data
6.1 Technical Data Chart
7.1 Parameter Table
8. Replacement Parts
8.1 Pre-filter Kit
8.2 Sintered Filter Kit
8.3 Blower Kit
Shroud
Warning
Nameplate
Control Pad
Viewing
Window
Disconnect
Operating
Handle
Potentiometer
and Local/Remote
Switch
Warning Plate
Pre-filters
IF 1767
Product
Nameplate
with Critical
Markings
Start/Stop/
Reset
(not shown)
Page 8
Page 8
Page 9
Page 9
Page 9
Page 10
Page 10
Page 10
Page 11
Page 11
Page 11
Page 11
Page 11
Page 11
Page 12
Page 12
Page 12
Page 12
Page 1
Advertisement
Table of Contents
Related Manuals for Eaton Crouse-Hinds Series
Summary of Contents for Eaton Crouse-Hinds Series
-
Page 1: Table Of Contents
8.5.1 Filter Shroud Installation Instructions Page 12 4.2 Disconnect and Lockout/Tagout Page 8 4.3 Drive Controls and Status Indication Page 8 4.4 PT (Potentiometer) and LR (Local/Remote) Page 8 IF 1767 • 09/15 Copyright 2015, Eaton’s Crouse-Hinds Division Page 1 ©... -
Page 2: Safety Instructions
To avoid personnel injury, DO NOT handle the blower or service the damage can result if the flat joint flame path is not properly fastened. enclosure while energized. IF 1767 • 09/15 Copyright 2015, Eaton’s Crouse-Hinds Division Page 2 ©... -
Page 3: Mechanical Installation
It is imperative that the enclosure be well ventilated to ensure reliable performance. Adequate space around the intake and exhaust of the enclosure MUST be accommodated. Eaton’s Crouse-Hinds Division recommends ‘x’ be a minimum of 12 inches (0.3 meters). 2.2 WEIGHTS Enclosure Weight (Approx.) -
Page 4: Dimensional Drawings
2.4 DIMENSIONAL DRAWINGS ACE Size 1 ACE Size 2 ACE Size 3 IF 1767 • 09/15 Copyright 2015, Eaton’s Crouse-Hinds Division Page 4 ©... -
Page 5: Mounting
Install wire guard using the bracket, screw and lock washer provided to the bottom filter(s). Align guard with notches within the bracket as shown. IF 1767 • 09/15 Copyright 2015, Eaton’s Crouse-Hinds Division Page 5 ©... -
Page 6: Line Feed
CAUTION Failure to add additional motor overload protection between the VFD and motor when required can cause motor failure and equipment damage. IF 1767 • 09/15 Copyright 2015, Eaton’s Crouse-Hinds Division Page 6 ©... -
Page 7: Factory Wiring Schematic
The control pad viewing window shows the control pad display Relay Output containing such information as drive status and operating data. Refer to the drive manufacturer’s manual for information regarding the control pad display. IF 1767 • 09/15 Copyright 2015, Eaton’s Crouse-Hinds Division Page 7 ©... -
Page 8: Disconnect And Lockout/Tagout
Note: As standard, speed control must either be programmed from the drive’s keypad, by remote analog signal (customer supplied) or by using the on board or option card communications capabilities. IF 1767 • 09/15 Copyright 2015, Eaton’s Crouse-Hinds Division Page 8 ©... -
Page 9: Explosive Event Required Maintenance
Inspect all other components and verify that they are in proper operating condition. Consult Eaton’s Crouse-Hinds Division for replacement parts as needed. -
Page 10: Power Loss (Heat Dissipation)
Parameters are set at the factory and must be maintained to ensure proper operation of cooling system and controls. Refer to drive manufacturer’s manual for additional parameter information. IF 1767 • 09/15 Copyright 2015, Eaton’s Crouse-Hinds Division Page 10 ©... -
Page 11: Pre-Filter Installation Instructions
However, should the need for replacement parts arise, they are avail- able through your Eaton’s Crouse-Hinds Division Distributor. Assistance 8.2.1 SINTERED FILTER INSTALLATION may also be obtained through your Sales Representative or the Eaton’s INSTRUCTIONS Crouse-Hinds Division Customer Service Department. -
Page 12: Window Kit (Ace Kit 7, Ace Kit 8)
All statements, technical information and recommendations contained herein are based on information and tests we believe to be reliable. The accuracy or completeness thereof are not guaranteed. In accordance with Eaton’s Crouse-Hinds Division’s “Terms and Conditions of Sale,” and since conditions of use are outside our control, the purchaser should determine the suitability of the product for his intended use and assumes all risk and liability whatsoever in connection therewith.