Advertisement
Actuators
Description
Straight
Straight w/rubber bushings
Right-angle
Right-angle w/rubber bushings
Angle Adjustable (vertical)
Angle Adjustable (vertical/horizontal) (Note 1)
Sliding Actuator (Note 2)
Dimensions and Mounting Hole Layouts
Straight Actuator (HS9Z-A51)
6.2
32.4
(6)
5.2
0.8
6.4
Actuator Mounting Hole Layout
(Straight, L-shaped)
Actuator Stop
(supplied with the actuator)
2-M4 Screw
(Note)
Straight Actuator w/Rubber Bushings (HS9Z-A51A)
7.3
43.8
• The mounting center distance is set to 12 mm
15.3
0.8
• The actuator has flexiblity to the direction
Actuator Stop (Note)
Washer (supplied with the switch)
2-ø10
2-ø9
Rubber Bushing
Angle Adjustable (vertical) (HS9Z-A53)
Actuator Stop
Film (supplied
with the actuator)
5
20
29
Angle Adjustment
(hexagon sockethead bolt)
Note: The actuator stop is supplied with the actuator and used when adjusting the actuator
position. Remove after the actuator position is determined.
Actuator Orientation
The orientation of actuator swing (horizontal/vertical) can be changed using the
orienting insert (white plastic) installed on the back of the actuator. Do not lose
the orientating insert, otherwise the actuator will not swing properly.
HS5E Miniature Interlock Switches with Solenoid
Actuator Retention Force
1400N minimum
500N minimum
1000N minimum
20
at factory. When 20-mm distance is required,
adjust the distance by moving the rubber
bushings.
indicated by the arrows. When 20-mm distance
is selected, the actuator swings vertically.
Actuator Mounting Hole Layout
Straight (with rubber bushings)
Right-angle (with rubber bushings)
2-M4 Screw
12
Note: Mounting centers can be widened
to 20 mm by moving the rubber
bushings.
18
Door hinge side
Actuator Mounting Hole Layout
(vertical swing)
2-M6 Screw
58
Part No.
HS9Z-A51
HS9Z-A51A
HS9Z-A52
HS9Z-A52A
HS9Z-A53
HS9Z-A55
HS9Z-SH5
Right-angle Actuator (HS9Z-A52)
33
2
7.2
4.5
0.8
Acuator Stop (supplied with the actuator) (Note)
Actuator Cover
Right-angle Actuator w/Rubber Bushings (HS9Z-A52A)
When mounted
(39.7)
When mounted (11.2)
0.8
Washer (supplied
Rubber Bushing
with the actuator)
When mounted (5)
0.8
Actuator Stop (plastic) (Note)
(supplied with the actuator)
Angle Adjustable (vertical/horizontal) (HS9Z-A55)
Horizontal Adjustment
3
Orienting
Insert
7
15
18.5
Vertical Adjustment
Orienting
Insert
Actuator Mounting Hole Layout
(horizontal/vertical swing)
2-M4 Screw
38
Note 1: When retention force of more than
500N is required, use HS9Z-A53.
Note 2: For details, see page 746.
7.2
1.6
• When the mounting center distance is set to
12 mm, the actuator has flexibility both
vertically and horizontally.
• When the mounting center distance is set to
20 mm, the actuator swings vertically. Adjust
the distance by moving the rubber bushings.
Angle Adjustment
(M3 Hexagon Socket Head Screw)
Actuator Stop
(Note)
1
29
3.6
Actuator Stop
(Note)
0.8
Angle Adjustment
(M3 Hexagon Socket Head Screw)
HS5E
Flush
Silhouette
Switches &
Pilot Lights
Display
Lights
LED
Illumination
Units
Display
Units
Safety
Products
Terminal
Blocks
Comm.
Terminals
AS-Interface
Relays &
Timers
Sockets
Circuit
Protectors
Power
Supplies
PLCs &
SmartRelay
Operator
Interfaces
Sensors
Control
Stations
Explosion
Protection
References
709
Advertisement
