Fisher & Paykel ACTIVESMART RS36A80 Installation Manual page 38

IMPORTANT!
Internal box
The standard appliance includes a stainless steel toe kick 4 (102mm) and the components required to mount the toe kick.
●
Door / d rawer Alternatively, the customer can supply their own custom toe kick 4 – 6 (102 – 152mm) for complete integration of the appliance.
E
●
trim install kit
For standard toe kick — 4" (102mm)
Dual adhesive tabs
Loosen the toe kick bracket screws (A) mid-way, and move
1
(2)
the brackets forward (B).
Miscellaneous
Z
components
#8x16 pan head screw (3)
Miscellaneous
Pre-align the toe kick by placing in front of the brackets until flush
2
items pack
with surrounding cabinetry. Once satisfied with the alignment,
set the toe kick aside and tighten the bracket screws to lock the
brackets in position.
Peel off the adhesive backing from one side of dual adhesive tabs
3
and attach to the brackets. Peel off the adhesive backing from the
Air flow divider
(1)
other side of dual adhesive tabs and attach the toe kick (C).
External box
Toe kick
(1)
Tools
Align the air flow divider underneath the grille tabs indicator
4
and clip onto the vanes of the bottom grille (D).
Cutter
Cross-head screwdriver
36
TOE KICK INSTALLATION
1. IF TOEKICK IS HIGHER THAN 4" USE SIDE CUTTER TO
CUT UNREQUIRED VANES FROM DOTTOM
2. DRILL HOLES THROUGH DIMPLES
3. USE PROVIDED SCREWS TO FIX GRILL TO
MATCHING HOLES ON PLASTIC PARTS
A
B
C
CUT UNREQUIRED VANES FROM DOTTOM
2. DRILL HOLES THROUGH DIMPLES
3. USE PROVIDED SCREWS TO FIX GRILL TO
1. IF TOEKICK IS HIGHER THAN 4" USE SIDE CUTTER TO
MATCHING HOLES ON PLASTIC PARTS
CUT UNREQUIRED VANES FROM DOTTOM
2. DRILL HOLES THROUGH DIMPLES
3. USE PROVIDED SCREWS TO FIX GRILL TO
MATCHING HOLES ON PLASTIC PARTS
For custom toe kick greater than 4" (102mm)
Remove the bottom grille from the bottom of the appliance.
5
Measure the required height for the bottom grille.
6
On a board, carefully score / c ut the excess vanes from
the bottom of the toe kick grille and discard (E).
Drill Ø 5/32 (4mm) holes into the dimples of the grille (F).
7
Cut excess vanes from the bottom of the grille
With the grille tabs facing upwards, align the grille to
8
the bottom of the plinth where the screw holes are
located and secure with #8x16 pan head screws (G).
1. IF TOEKICK IS HIGHER THAN 4" USE SIDE CUTTER TO
CUT UNREQUIRED VANES FROM DOTTOM
2. DRILL HOLES THROUGH DIMPLES
3. USE PROVIDED SCREWS TO FIX GRILL TO
MATCHING HOLES ON PLASTIC PARTS
Align the air flow divider underneath the grille tabs
9
indicator and clip onto the vanes of the bottom grille (H).
D
SCALE 2 : 1
1. IF TOEKICK IS HIGHER THAN 4" USE S
CUT UNREQUIRED VANES FROM DO
2. DRILL HOLES THROUGH DIMPLES
3. USE PROVIDED SCREWS TO FIX GRIL
MATCHING HOLES ON PLASTIC PAR
F
DETAIL A
SCALE 1 : 1
Grille tabs
DETAIL D
DETAIL A
SCALE 1 : 1
DET
SCAL
E
G
Front right view
DETAIL A
SCALE 1 : 1
DETAIL B
SCALE 2 : 5
H