Fisher & Paykel ACTIVESMART RS9120W Installation Manual
Integrated door/drawer refrigerator
Hide thumbs
Also See for ACTIVESMART RS9120W:
- Installation manual (48 pages) ,
- User manual (44 pages) ,
- Dual installation manual (16 pages)
Related Manuals for Fisher & Paykel ACTIVESMART RS9120W
Summary of Contents for Fisher & Paykel ACTIVESMART RS9120W
- Page 1 ACTIVESMART™ INTEGRATED DOOR/DRAWER REFRIGERATOR RS9120W models INSTALLATION GUIDE NZ AU GB IE HK SG IN 846806C 07.18...
-
Page 3: Table Of Contents
CONTENTS FOLLOW THE INSTALLATION SEQUENCE RELEVANT TO YOUR CABINETRY 1 SAFETY AND WARNINGS 2 COMPONENTS LIST 3 PRODUCT AND CAVITY DIMENSIONS 4 CABINETRY OPTIONS 5 STAINLESS STEEL DOOR PANEL AND TOE KICK DIMENSIONS 6 CUSTOM DOOR PANEL AND TOE KICK DIMENSIONS 7 CUSTOM DOOR PANEL INSTALLATION DIMENSIONS 8 DOOR OPENING ROTATION 9 ELECTRICAL AND PLUMBING !0 BEFORE INSTALLATION... -
Page 5: Safety And Warnings
SAFETY AND WARNINGS IMPORTANT! WARNING! The water connection to your Ice & water refrigerator must be installed by an ● ● authorised plumber or Fisher & Paykel trained and supported service technician Electric Shock Hazard and comply with all state and local laws. Read and follow the safety and warnings outlined in this installation Installation and use MUST comply with all state and local plumbing codes. -
Page 6: Components List
COMPONENTS LIST MI (miscellaneous items) pack — included with the refrigerator Anti-tip bracket fittings — included with the refrigerator ACTIVESMART™ INTEGRATED ACTIVESMART™ DOOR/DRAWER REFRIGERATOR INTEGRATED REFRIGERATOR RS9120W models RS90A, RS9120W, RS36A72, RS36A80 & RS36W80 models SERVICE & WARRANTY SERVICE ET GARANTIE ΣΈΡΒΙΣ ΚΑΙ ΕΓΓΎΗΣΗ SERVIZIO E GARANZIA SERVICE &... - Page 7 COMPONENTS LIST Water fittings — included with the refrigerator Door panel set Water filter (1x) Collet locking clip (1x) Tap adaptor (1x) Fisher & Paykel Custom door (Stainless steel) panel set is door panel set is only applicable not included with for non-Water the refrigerator dispensing models.
-
Page 8: Product And Cavity Dimensions
PRODUCT AND CAVITY DIMENSIONS IMPORTANT! For ease of installation, ensure cavity width is consistent top to bottom and height is consistent left to right. PLAN VIEW Note: image shows custom panel flushed with edge of cabinetry Note: Shown with custom panel and handle attached to fridge CAVITY DIMENSIONS Overall height of cavity... -
Page 9: Cabinetry Options
CABINETRY OPTIONS FRAMELESS CABINETRY FRAMED CABINETRY (Frameless: Aligns the product with the cabinetry) (Framed: Aligns the product with the frame of the cabinetry) Frameless Framed Flush Proud installation installation Note: Shown with custom panel and handle attached to fridge Note: Shown with custom panel Note: Shown with custom panel and handle attached to fridge and handle attached to fridge... -
Page 10: Stainless Steel Door Panel And Toe Kick Dimensions
STAINLESS STEEL DOOR PANEL AND TOE KICK DIMENSIONS RD3680 DOOR PANEL SET RD3684 DOOR PANEL SET RD3680 RD3684 DOOR PANEL SETS DIMENSIONS TOE KICK PANEL DIMENSIONS Height of top door panel 1150 1252 Height of toe kick panel Height of bottom drawer panel Depth of toe kick (measured from front of door panels) Depth of product front panels... -
Page 11: Custom Door Panel And Toe Kick Dimensions
CUSTOM DOOR PANEL AND TOE KICK DIMENSIONS Note: top trim supplied for Note: Top trim supplied for 84" installation 2134mm installation PROFILE VIEW CUSTOM PANEL DIMENSIONS Height of top door panel 1150 – 1252 Width of top door and bottom drawer panel Height of bottom drawer panel 722 – 772 PROFILE VIEW... -
Page 12: Custom Door Panel Installation Dimensions
CUSTOM DOOR PANEL INSTALLATION DIMENSIONS The drawings below apply to Automatic ice models, (RS9120W(R/L)J). Dimensions apply for the preparation and installation of custom door panels. For Dwg and Dxf files of the below panel preparation download the folder on thekitchentools.fisherpaykel.com 764mm 558mm 347mm... -
Page 13: Door Opening Rotation
DOOR OPENING ROTATION 115° DOOR OPENING 90° DOOR OPENING Wall Wall (FULL ROTATION) 115° DOOR OPENING 115° DOOR OPENING 90° DOOR OPENING 90° DOOR OPENING [FULL ROTATION] [FULL ROTATION] For 90° door swing a hinge limiting pin is supplied with RS9120WRU RS9120W(R/L)J your refrigerator. -
Page 14: Electrical And Plumbing
ELECTRICAL AND PLUMBING WARNING! Electrical shock hazard. Assume all parts are live. Disconnect supply before servicing and installation. 756mm Left side of cavity 143mm Floor 51mm 73mm Electrical and water connections must be within this space if located behind the refrigerator Electrical Plumbing REAR OF CAVITY... - Page 15 ELECTRICAL AND PLUMBING Maximum distance of hose and power cord Power cord (excl. plug) – 800mm (31 1/2”) LEFT HAND SIDE RIGHT HAND SIDE Water inlet hose – 1350mm (53”) Water inlet hose – 2120mm (84 1/4”) Power cord (excl. plug) – 2051mm (80 3/4”) Power cord (excl.
-
Page 16: Before Installation
BEFORE INSTALLATION IMPORTANT! Ensure your refrigerator is not exposed to any heat generating appliances eg cooktop, oven or dishwasher. ● ● The refrigerator has front and rear rollers for moving the refrigerator forward and backward. Do not move the refrigerator sideways to avoid damaging the rollers or floor covering/surface. ●... -
Page 17: Attach Anti-Tip Bracket
ATTACH ANTI-TIP BRACKET IMPORTANT! WARNING! Ensure the refrigerator door is closed when rolling into cabinetry. Read the following reminders before fastening with masonry plugs and/or screws: ● ● DO NOT attempt to open the door until refrigerator is fully installed. Ensure the screws avoid electrical, gas and water conduits. -
Page 18: Attach Top Trim - For 2134Mm Cavity
ATTACH TOP TRIM (FOR 2134mm CAVITY HEIGHT) WARNING! Be careful when working with the refrigerator outside of the finished enclosure. Ensure that the refrigerator is secured to prevent tipping forward. Tipping of refrigerator can lead to serious injury or death. Ensure all external packaging material is removed from the refrigerator before installation. -
Page 19: Attach Side Brackets And Door Studs
ATTACH SIDE BASE BRACKETS AND DOOR STUDS LH orientation 1 – 2 turns Ensure all external packaging materials are removed Secure M8 studs into the refrigerator doors. Loosely screw (1 – 2 turns) M5x10 pan head from the refrigerator before installation. Ensure the open end faces the top and the Phillips screws into doors. - Page 20 CONNECT TO WATER AND ELECTRICAL SUPPLY IMPORTANT! The water connection instructions below are intended only for the professional installer. ● ● Ensure water tubing is routed away from any sharp objects, sharp corners and not in a location where it can be kinked or squashed. ●...
-
Page 21: Connect To Water And Electrical Supply
CONNECT TO WATER AND ELECTRICAL SUPPLY Connecting to the power outlet IMPORTANT! At the back of your refrigerator, connect the refrigerator to the electrical supply (230VAC, 50Hz) with the fitted plug and lead, and turn on. Follow the steps below to avoid running over the hose that can cause Ensure the refrigerator is connected to its own isolating switch (A). -
Page 22: Align Your Product Inside Cabinetry
ALIGN YOUR PRODUCT INSIDE CABINETRY IMPORTANT! Ensure that all four corners of the refrigerator are supported firmly onto the floor Note: Maximum turn is 20mm. ● ● to eliminate any movement. Use low torque setting to avoid damage to height adjustment system. ●... - Page 23 INSTALL WATER FILTER AND TOE KICK GRILLE IMPORTANT! The water filter head must be firmly pushed into the product and secured. incorrect installation can lead to water leaks. ● ● Installing the water filter Installing the toe kick filter and grille Pull the freezer drawer out slightly and insert the filter into the casing at the bottom Remove filter from inside the product.
- Page 24 ASSEMBLE DOOR PANEL SET The assembly of Fisher & Paykel (Stainless steel) door panels and custom door panels are outlined below. To protect the finish of the Fisher & Paykel Stainless steel door panels, leave protective film on the panels when hanging and remove film only when installation is complete. If using custom door panels, ensure they are prepared as per ‘Custom door panel installation dimensions’...
- Page 25 HANG WATER DISPENSING DOOR PANEL For Fisher & Paykel Stainless steel door panels only. Remove the external display Angle top display tabs into the Connect display harness onto the refrigerator door module from inside the product. door panel. Ensure the harness by inserting firmly until you feel it clip securely (B).
- Page 26 HANG NON-WATER DISPENSING DOOR PANELS For Fisher & Paykel Stainless steel door panels only. IMPORTANT! Remove protective film from white product doors before hanging door panels. Hang all door panels onto M8 studs and align the side bracket forks onto the refrigerator door (A).
- Page 27 ATTACH FIXING BRACKETS Carefully open the refrigerator door to attach Slide screw cover in between the fixing bracket the fixing brackets. Place fixing bracket over the and the side bracket on the refrigerator. side of the refrigerator and secure mid-way with M5x8 countersunk Phillips screws (2x).
- Page 28 ATTACH TOE KICK The standard refrigerator includes a stainless steel toe kick 102mm and the hardware required to mount the toe kick 102mm. Alternatively the customer can supply their own custom toe kick 102 – 152mm for complete integration of the refrigerator. Installing toe kick Unscrew the toe kick bracket screws mid-way, and bring forward (A and B).
- Page 29 ATTACH COVERS AND DOOR/DRAWER TRIMS If applicable, remove any remaining protective film on your door panels. Open the refrigerator door, firmly push top cover (A) over the top studs. Press firmly to install on the underside Press the 3M Dual Lock™ tabs together to of the drawer top trim in the indicated form pairs (D) and remove the adhesive locations (E).
- Page 30 ATTACH BOTTOM TOE KICK DETAIL A SCALE 1 : 1 For custom toe kick greater than 102mm For toe kick installation at 102mm Grille tabs DETAIL A SCALE 1 : 1 DETAIL A Cut un-required vanes from the bottom of the grille SCALE 1 : 1 Measure the required height for the bottom grille.
- Page 31 TWO METHODS ARE AVAILABLE FOR ATTACHING SIDE TRIM BRACKETS: [A] FLEXIBLE SPRING CLIP METHOD – RECOMMENDED METHOD [B] FIXED SCREW METHOD – METHOD TO USE IF CABINET IS NOT TO SPECIFICATION (Attempt method [A]. If method [A] results in poor fitment of side trims due to cabinetry that is uneven or out of specification, use method [B]). ATTACH SIDE TRIM BRACKETS –...
- Page 32 ATTACH SIDE TRIM BRACKETS – [A] FLEXIBLE SPRING CLIP METHOD Spring clip Side trim lip Top view of spring clip correctly inserted between side trim and side trim bracket Insert the spring clip into the gap between the side trim and side trim bracket, Open refrigerator doors.
- Page 33 ATTACH SIDE TRIM BRACKETS – [B] FIXED SCREW METHOD If method [A] Flexible spring clip method, has resulted in poor fitment of side trims due to cabinet being out of spec, use method [B] Fixed screw method. 50mm IMPORTANT! Before installing your refrigerator, ensure the dimensions of the finished enclosure are correct for your refrigerator following the ‘Product and cavity dimensions’...
- Page 34 ATTACH SIDE TRIM BRACKETS – [B] FIXED SCREW METHOD Side trim Suggestio engageme “ensure th Side trim bracket Top view of side trim engaged correctly in side trim bracket IMPORTANT! Place the side trim against the alcove side wall with Engage the side trim with the brackets by pushing the the shorter lip facing the bottom (D).
- Page 35 ADJUST HINGE TENSIONING SCREWS Hinge tensioning screw Hinge tensioning screws can be tightened if increased door closing force is required. Tighten the hinge tensioning screws to ensure the top door shut on their own when pushed within the self close activation range. The hinge tensioning screw is located in the top door hinges. To tighten the screw, rotate the screw to the right (A).
- Page 36 FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER All models Check all parts are installed. Ensure the refrigerator is level. Ensure the refrigerator is securely fastened to the cabinetry with the supplied anti-tip bracket and fittings. Ensure the door/drawer can open and close freely with no resistance from surrounding cabinetry.