Assa Abloy Sargent 7300 Series Installation Instructions Manual

Assa Abloy Sargent 7300 Series Installation Instructions Manual

Multi-point lock

Advertisement

Quick Links

Installation Instructions
7300 Series
Multi-Point Lock
Important
The latches, rods, and cassette are pre-installed.
This product must be installed by a factory trained technician.
WARNING
This product can expose you to lead
which is known to the state of California
to cause cancer and birth defects or other
reproductive harm. For more information
go to www.P65warnings.ca.gov.
1-800-727-5477 • www.sargentlock.com
Copyright © 2017, 2019, 2020 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part
without the express written permission of SARGENT Manufacturing Company is prohibited.
A8270A 02/20

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Sargent 7300 Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Assa Abloy Sargent 7300 Series

  • Page 1 Installation Instructions 7300 Series Multi-Point Lock Important The latches, rods, and cassette are pre-installed. This product must be installed by a factory trained technician. WARNING This product can expose you to lead which is known to the state of California to cause cancer and birth defects or other reproductive harm.
  • Page 2: Table Of Contents

    7300 Series Multi-Point Lock Installation Instructions Table of Contents Package Contents ............. . .4 Tools Required .
  • Page 3 7300 Series Multi-Point Lock Installation Instructions Addendum ..............16 Check Door .
  • Page 4: Package Contents

    7300 Series Multi-Point Lock Installation Instructions Package Contents Part Number Description 82-5342 Multipoint cassette 82-5345 Trim mounting screw pack 82-5346 Top/bottom case mounting screw pack 82-5347 Top strike pack 82-5348 Bottom strike pack 82-5349 Mortise mounting/reinforcement pack 82-5350 Center strike pack Dogging indicator (includes item 11) (specify finish) 82-5386 Top case and rod assembly (specify door size)
  • Page 5: Tools Required

    7300 Series Multi-Point Lock Installation Instructions Tools Required Tape measure Hammer Flashlight 1/8" Allen 3/32" Allen 5/32" Allen (supplied) (supplied) Drill 1/8" Masonry #3 Phillips Slotted #1, #2, #3 Chisel 3/8" drill bit screwdriver Phillips head Anchor set screwdrivers Tools Required for Electronic Access Control (EAC) Shield #29 Drill bit #8-32 Tap (.136")
  • Page 6: Installation

    7300 Series Multi-Point Lock Installation Instructions Installation Check Door Verify the door is: • Correct size and hand for opening. • Correctly prepared to Template 4740. Outswing Door IMPORTANT Shown If measurement is incorrect, DO NOT PROCEED WITH INSTALLATION. Contact door manufacturer. (Figure 1) of Lockbody 39-9/16"...
  • Page 7: Install Center Strike Into Door Frame

    7300 Series Multi-Point Lock Installation Instructions Installation (cont.) Install Center Strike into Door Frame • Install two (2) ¼-20 socket cap flat head screws. (Figure 3) Remove Retractor Inserts Figure 3 WARNING The door now has the ability to latch. (Figure 4) Figure 4 Check Latches (uninstalled) •...
  • Page 8: Install Bottom Strike

    7300 Series Multi-Point Lock Installation Instructions Installation (cont.) Install Bottom Strike • Close the door and mark the location of the bottom bolt. ✓ 3/8" MAX Bottom of door to floor. Figure 7 • Open the door and place the strike over the bottom bolt location. Mark the location of the bottom strike pocket and hole locations.
  • Page 9 7300 Series Multi-Point Lock Installation Instructions Installation (cont.) Install Bottom Strike (cont.) Flush Mount (Figure 9) Surface Mount (Figure 12) Chisel the bottom strike pocket Mortise the strike into the floor 1/4" deep. 1" deep to ensure the bolt has full projection. (Optional for 3/8"...
  • Page 10: Top And Bottom Latch Adjustment

    7300 Series Multi-Point Lock Installation Instructions Installation (cont.) Top and Bottom Latch Adjustment TOP OF DOOR • With the door hung, measure the clearance 1/16" Bolt to strike clearance. between the top and bottom bolts and strikes. (Figure 15) BOTTOM OF DOOR Note: If both measurements equal 1/16"...
  • Page 11 7300 Series Multi-Point Lock Installation Instructions Installation (cont.) Top and Bottom Latch Adjustment (cont.) TOP OF DOOR Using the supplied 3/32" Allen wrench, rotate the top 1/16" Bolt to strike clearance. or bottom worm gears according to the directions below (Figure 19). Bolt to strike clearance should equal 1/16".
  • Page 12: Mortise Lock Install

    7300 Series Multi-Point Lock Installation Instructions Installation (cont.) Mortise Lock Install • Remove the two (2) #12-24 x1" flat head mounting screws. (Figure 22) Figure 22 • Remove the mortise lock filler and discard. (Figure 23) Mortise Lock Filler • Install the mortise lock, two (2) #12-24 x1" flat head mounting screws, outside front, and two (2) #8-32 x1/4"...
  • Page 13: Final Mortise Lock And Trim Installation

    7300 Series Multi-Point Lock Installation Instructions Installation (cont.) Final Mortise Lock and Trim Installation Follow the supplied mortise lock installation instructions for trim and other function related hardware. Electronic Access Control (EAC) Reader and Controller Installation Follow supplied EAC Installation Instructions (if applicable). Key Override with Deadbolt Function Operation Check Verify hand and bevel of door to determine direction to rotate key and lever.
  • Page 14: Optional Installation

    7300 Series Multi-Point Lock Installation Instructions Optional Installation Dogging Indicator Installation • Ensure the door is latched and all bolts are projected. • Place the plastic field template on the pin in the top rod through the oval cut-out in the door. (Figure 27) Front View Side View...
  • Page 15 7300 Series Multi-Point Lock Installation Instructions Optional Installation (cont.) Dogging Indicator Installation (cont.) Install the indicator on the inside of the door using supplied 10-24 x 2" oval head screws. Make sure the control fingers grab the top rod pin as shown. (Figure 30) Side View Control Fingers Figure 30...
  • Page 16: Addendum

    7300 Series Multi-Point Lock Installation Instructions Addendum This addendum is to be used as a reference for pre-installed hardware (latches and cassette). The following steps are for ease of reference as they have been completed in advance by the door manufacturer.
  • Page 17: Install Lockbody Cassette (Lbc)

    7300 Series Multi-Point Lock Installation Instructions Addendum (cont.) Install Lockbody Cassette (LBC) LBC Gear Worm Gear • Using the supplied 3/32" Allen wrench, rotate both LBC worm gears to align slots in the LBC gears to the orientation shown. (Figure 34) Alignment is needed for proper installation of the rod guide.
  • Page 18: Feed Top Rod Into Door

    7300 Series Multi-Point Lock Installation Instructions Addendum (cont.) Feed Top Rod into Door • Orient the latch chassis as shown. Rotate the rod and rod guide so the rod guide tab faces up. Slide the rod assembly into the door. Make sure the rod guide remains in the correct orientation with the guide tab facing up.
  • Page 19: Troubleshoot Latch Installation

    7300 Series Multi-Point Lock Installation Instructions Addendum (cont.) Troubleshoot Latch Installation Misaligned Rod Guide Rod Guide • If the latch will not fully seat in the door, rod or rod guide is not aligned properly with LBC gear. (Figure 40) REPEAT: REPEAT: Step 6E to align.
  • Page 20: Secure Top Latch

    7300 Series Multi-Point Lock Installation Instructions Addendum (cont.) Secure Top Latch • Install four (4) 10-24 oval head screws on the face of the door. (Figure 42) Figure 42 • Install six (6) 1/4-20 flat head screws in the top edge of the door.
  • Page 21: Bottom Latch Installation

    7300 Series Multi-Point Lock Installation Instructions Addendum (cont.) Bottom Latch Installation REPEAT Steps 5e through 5k to install bottom latch. (Figure 45) Figure 45 Check Latch • Remove the bolt retainer clips from the top and bottom latch assemblies. Figure 46 (Figure 46) • Insert mortise trim in the door prep and cassette and rotate to verify latches fully retract (Figure 47).
  • Page 22: Mortise Reinforcer And Mortise Lock Installation

    7300 Series Multi-Point Lock Installation Instructions Addendum (cont.) Mortise Reinforcer and Mortise Lock Installation • Remove the two (2) #12-24x1" flat head LBC mounting screws that are securing the lockbody case in the door. (Figure 50) • Place mortise reinforcer into the door. •...
  • Page 23 7300 Series Multi-Point Lock Installation Instructions 1-800-727-5477 • www.sargentlock.com A8270A 02/20 Copyright © 2017, 2019, 2020 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without the express written permission of SARGENT Manufacturing Company is prohibited.
  • Page 24 SARGENT Manufacturing Company 100 Sargent Drive New Haven, CT 06511 USA 800-727-5477 www.sargentlock.com Founded in the early 1800s, SARGENT ® is a market leader in locksets, cylinders, door closers, exit devices, electro- mechanical products and access control systems for new construction, renovation, and replacement applications. The company’s customer base includes commercial construction, institutional, and industrial markets.

Table of Contents