Table of Contents
Advertisement
Quick Links
International registered trademark n. 2.777.971
SEAGEAR
Cod. 1180MEC0
INSTALLATION MANUALS
AND SAFETY INFORMATION
SEA USA Inc.
10850 N.W. 21st unit 160 DORAL MIAMI
Florida (FL) 33172
Phone:++1-305.594.1151 Fax: ++1-305.594.7325
Toll Free: 800.689.4716
web site: www.sea-usa.com
e-mail: sales@sea-usa.com
67410830
REV.06 - 06/2014
Advertisement
Table of Contents
Related Manuals for SEA SEAGEAR 1180MEC0
Summary of Contents for SEA SEAGEAR 1180MEC0
- Page 1 International registered trademark n. 2.777.971 SEAGEAR Cod. 1180MEC0 INSTALLATION MANUALS AND SAFETY INFORMATION SEA USA Inc. 10850 N.W. 21st unit 160 DORAL MIAMI Florida (FL) 33172 Phone:++1-305.594.1151 Fax: ++1-305.594.7325 Toll Free: 800.689.4716 web site: www.sea-usa.com e-mail: sales@sea-usa.com 67410830 REV.06 - 06/2014...
-
Page 2: Table Of Contents
SEAGEAR International registered trademark n. 2.777.971 TABLE OF CONTENTS A) SAFETY INSTRUCTIONS (UL)......................3 B) MECHANICAL INSTALLATION FEATURES AND SPECIFICATIONS......................5 GATE WARNINGS..........................6 PRECAUTIONS.............................6 TYPE OF INSTALLATION........................7 INSTALLATION AND FIXATION OF THE MOTOR REDUCER.............7 CHAIN INSTALLATION..........................7 LIMIT SWITCH SET UP..........................8 MANUAL RELEASE SYSTEM.......................9 GENERAL SWITCH..........................10 RISK EXAMINATION..........................10 PERIODICAL MAINTENANCE......................10... - Page 3 SEAGEAR International registered trademark n. 2.777.971 Details General An appliance shall be provided with an instruction manual. The instruction manual shall give instructions for the installation, operation, and user maintenance of the appliance. The installation instructions shall specify the need for a grounding-type receptacle for connection to the supply and shall stress the importance of proper grounding.
- Page 4 SEAGEAR International registered trademark n. 2.777.971 g) The Stop and/or Reset button must be located in the line-of-sight of the gate. Activation of the reset control shall not cause the operator to start. h) A minimum of two (2) WARNING SIGNS shall be installed, one on each side of the gate where easily visible. i) For gate operators utilizing a non-contact sensor: 1) See instructions on the placement of non-contact sensors for each Type of application, 2) Care shall be exercised to reduce the risk of nuisance tripping, such as when a vehicle, trips the sensor while the gate is...
-
Page 5: B) Mechanical Installation
SEAGEAR International registered trademark n. 2.777.971 MECHANICAL INSTALLATION SEAGEAR is an oil-bathed motor- DIMENSIONS reducer created for sliding gates automation. The motor-reducer irreversibility allows a perfect and safe gate closing avoiding the setup of an electrolock and in case of power supply lacking, the release device which is in the frontal part of the motor- reducer allows the manual opening and... -
Page 6: Gate Warnings
Install the warning signs, on both sides of the gate which informs the pedestrians about the danger they run when passing or resting in the environment of the gate (fig. 10). Important: For a higher security, SEA advices to install infrared photocells. Fig. 1 Fig. 2 Fig. 3 Fig. -
Page 7: Type Of Installation
SEAGEAR International registered trademark n. 2.777.971 MECHANICAL INSTALLATION 3. TYPE OF INSTALLATION 4.3. Before piercing the concrete square for the fixation of the motor reducer, make sure that the distance between the centre of the oblong A front installation is the right and only possible installation, it is highly and the gate is of 3”... -
Page 8: Limit Switch Set Up
SEAGEAR International registered trademark n. 2.777.971 MECHANICAL INSTALLATION 5.3. Install a fillet chain tensioner to two extremity of the gate to regulate the tension of the chain. Note: Execute this last operation with motor completely released using the provided special release key. 6. -
Page 9: Manual Release System
SEAGEAR International registered trademark n. 2.777.971 MECHANICAL INSTALLATION To have a more accurate adjustment, act on the adjusting screws in the 6.2. To install and adjust the limit switches in opening, see the following instructions: testing phase, after having executed the previous operations. Notice: to adjust the way of the gate run in opening and in closing, make reference to the instructions of the electronic control unit. -
Page 10: General Switch
Any switch (2) which allows to turn on or off the electric initiative taken without SEA USA Inc. explicit authorization will preserve the power supply of the automation (Fig. 27). This switch manufacturer from whatsoever responsibility. -
Page 11: C) Sales Conditions And Warranty
SEA. Recognized defects, whatever their nature, will not produce any responsibility and/or damage claims to SEA USA Inc and SEA s.r.l. Warranty shall not cover any required labor activities. Warranty will in no case be recognized if alterations and any other changes will be found on products. Warranty will not cover damages caused by carriers, expendable materials and faults due to improper use with the products specifications. - Page 12 International registered trademark n. 2.777.971 SEA USA Inc. 10850 N.W. 21st unit 160 DORAL MIAMI Florida (FL) 33172 Phone:++1-305.594.1151 Fax: ++1-305.594.7325 Toll Free: 800.689.4716 web site: www.sea-usa.com e-mail: sales@sea-usa.com...
Need help?
Do you have a question about the SEAGEAR 1180MEC0 and is the answer not in the manual?
Questions and answers