Advertisement
Quick Links
Advertisement
Related Manuals for MiTAC ND108T
Summary of Contents for MiTAC ND108T
- Page 1 MiTAC ND108T Quick Installation Guide 2020/7/30...
- Page 2 MB Placement 12V internal 4- pin DC-in 1 x Line- connector out/Mic-in 1 x UART header for debugging 1 x USB2.0 ports header 1 x USB 2.0 OTG 1 x Power port Header for Switch programming 1 x Raspberry Pi 40-pin header...
- Page 3 Pin Definition (1/3) (J1)
- Page 4 Pin Definition (2/3) (J13) (J22)
- Page 5 Pin Definition (3/3) Raspberry Pi 40-pin header...
- Page 6 How to insert the Micro SD card...
- Page 7 How to enter U-boot The bring up sequences will count-down 3 seconds in u-boot. Please use RS232 to connect ND108T’s J22 (UART_TX and UART_RX), and press any key in 3 seconds to enter u-boot.
- Page 8 MiTAC Computing Technology Corporation. The information in this document has been carefully checked and is believed to be accurate. However, MiTAC Computing Technology Corporation assumes no responsibility for any errors that may appear in this document. The material contained herein is for informational purposes only.
-
Page 9: Table Of Contents
2 Yocto Image Update ................... 3 3 Android Image Update ................7 THIS DOCUMENT IS PROPERTY OF MiTAC COMPUTING TECHNOLOGY CORPORATION. ITS USE IS AUTHORIZED ONLY FOR RESPONDING TO A REQUEST OR FOR QUOTATION OR FOR THE PERFORMANCE OF WORK FOR MITAC COMPUTING TECHNOLOGY CORP. ALL QUESTIONS MUST... -
Page 10: Purpose
Project: ND108T ND108T Yocto & Android Image Update SOP 1 Purpose This Standard Operation Procedure (SOP) describes the usage of Yocto & Android image update method for ND108T project. 2 Yocto Image Update 1) Configure DIP switches SW1 [1 2] to [OFF ON] and SW2 [1 2 3 4] to [OFF OFF ON OFF]. - Page 11 Project: ND108T ND108T Yocto & Android Image Update SOP 2) Connect USB cable between your J19 connector of ND108T device and desktop PC, then plug-in power source to J1 connector. 3) Unzip Yocto image (ND108T_Yocto_xx.xx.xxxxxx.zip) in your Windows 10 desktop-PC.
- Page 12 Project: ND108T ND108T Yocto & Android Image Update SOP 4) Launch the batch file “update_image.bat” to update image. 5) Wait for the upgrade progress is done. MiTAC Computing Technology Corp. Proprietary and Confidential PAGE 5 OF 10 November 01, 2017...
- Page 13 Project: ND108T ND108T Yocto & Android Image Update SOP 6) Unplug USB cable and power source, and configure DIP switch SW1 [1 2] to [ON OFF] to Internal Boot Mode. 7) Plug in power source to boot up device; if you have the debug board and connect to desktop-PC, then you could get logs.
-
Page 14: Android Image Update
DIP3 DIP4 Boot Media Configuration eMMC microSD 2) Connect USB cable between your J19 connector of ND108T device and desktop PC, then plug-in power source to J1 connector. MiTAC Computing Technology Corp. Proprietary and Confidential PAGE 7 OF 10 November 01, 2017... - Page 15 Project: ND108T ND108T Yocto & Android Image Update SOP 3) Unzip Android image (ND108T_8MQ_4G32G_Android_xx.xx.xxxxxx.zip) in your Windows 10 desktop- 4) Launch the batch file “update_image.bat” to update image. MiTAC Computing Technology Corp. Proprietary and Confidential PAGE 8 OF 10 November 01, 2017...
- Page 16 Project: ND108T ND108T Yocto & Android Image Update SOP 5) Wait for the upgrade progress is done. MiTAC Computing Technology Corp. Proprietary and Confidential PAGE 9 OF 10 November 01, 2017...
- Page 17 Project: ND108T ND108T Yocto & Android Image Update SOP 6) Unplug USB cable and power source, and configure DIP switch SW1 [1 2] to [ON OFF] to Internal Boot Mode. 7) Plug in power source to boot up device; if you have the debug board and connect to desktop-PC, then you could get logs.
- Page 18 MiTAC I.MX8M Product Series ME1-108T / ND108T Linux BSP User Guide...
- Page 19 MiTAC I.MX8M series product (Box PC: ME1-108T, MB: ND108T), MiTAC provides the following Linux BSP (Board support Package) software for developer to develop your targeting Linux OS. These BSPs with source code are customizable, allowing the developers to specify which drivers and routines should be included in the build based on your targeting Linux version and software options.
- Page 20 Here 3. BSP for Android 9 This release is based on NXP BSP layer for Android 9 framework and MiTAC extends this layer to support our I.MX8M product related functions. Android 9 (Pie, Kernel version 4.14.98) BSP, including source code and files for: ...
- Page 21 4. Customization Support For other customization items beyond our standard BSP coverage above, please contact our sales window for more business discussion and it will only support by requested. The customization items could be: Yocto and Android sample image customization ex: UI customization, new Android option enable/disable, new App pre- install ...
Need help?
Do you have a question about the ND108T and is the answer not in the manual?
Questions and answers