Playback; Basic Procedure; Selecting The Multi Ch Input Component - Yamaha RX-Z11 Owner's Manual

Playback

Caution
Extreme caution should be exercised when you play back CDs
encoded in DTS. If you play back a CD encoded in DTS on a
DTS-incompatible CD player, you will only hear some
unwanted noise that may damage your speakers. Check whether
your CD player supports CDs encoded in DTS. Also, check the
sound output level of your CD player before you play back a CD
encoded in DTS.
y
To play DTS-encoded CDs when using a digital audio connection, set
"Decoder Mode" in "Input Select" to "DTS" before playback (see
page 97).
Before performing the following operations, set the operation mode
selector on the remote control to F AMP.

Basic procedure

1
Turn on the video monitor connected to this unit.
y
• If you connect two video monitors to the HDMI OUT jacks of this
unit, press CHDMI OUT repeatedly to select the active video
monitor.
• You can control this unit by using the graphical user interface (GUI)
screen. See page 57 for details.
• You can turn on or off the short message displays in the video
monitor. See page 108 for details.
Rotate the D INPUT selector (or press one of the
2
input selector buttons (3)) to select the desired
input source.
The name of the currently selected input source appears in the
front panel display and in the short message display for a few
seconds.
Available input sources
NET V-AUX CBL
VCR DVR
USB DOCK SAT
(U.S.A. model)
3
Start playback on the selected source component or
select a broadcast station.
• Refer to the instruction manuals for the source component.
• See page 68 for details about FM/AM tuning instructions.
• (U.S.A. and Canada models only) See page 74 for details
about XM Satellite Radio tuning instruction.
• See page 78 for details about the iPod operation with this
unit.
• See page 80 for details about playback of Internet Radio
programs and the music contents in the PC or USB storage
devices.
54
En
BD MD
DTV DVD CD-R CD PHONO MULTI CH TUNER XM
HD DVD TAPE
D V D
Currently selected input source

Playback

Rotate E VOLUME (or press J VOLUME +/–) to
4
adjust the volume to the desired output level.
Control range: Mute, –80.0 dB (minimum) to
y
See page 65 to adjust the level of each speaker.
Rotate the M PROGRAM selector (or press one of
5
the sound field program selector buttons (Q)
repeatedly) to select the desired sound field
program.
The name of the selected sound field program appears in the
front panel display and in the short message display. See
page 58 for details about sound field programs.
Currently selected sound field program category
Notes
• Sound field programs cannot be selected when the component
connected to the MULTI CH INPUT jacks is selected as the input
source (see page 54).
• Press HSTRAIGHT and the rotate MPROGRAM to select the
desired sound field program when "TUNER" or "XM" (U.S.A. and
Canada models only) is selected as the input source.
y
• Choose a sound field program based on your listening preference, not
merely on the name of the program.
• When you select an input source, this unit automatically selects the
last sound field program used with the corresponding input source.
Selecting the MULTI CH INPUT
component
Use this feature to select the component connected to the MULTI
CH INPUT jacks (see page 37) as the input source.
Rotate the D INPUT selector (or press 3 MULTI) to
select "MULTI CH".
y
Use "MULTI CH" menu in "Input Select" to set the parameters for MULTI
CH (see page 98).
Note
Sound field programs cannot be selected when the component connected to
the MULTI CH INPUT jacks is selected as the input source (see page 58).
+16.5 dB (maximum)
M o v i e
S c i - F i
Currently selected sound field program