Manual Setup (Volume) - Yamaha RX-Z11 Owner's Manual

Graphical user interface (GUI) menu
■ Speaker Level (Speaker level)
Use this feature to manually balance the speaker levels between the
front left or surround left speakers and each speaker selected in
"Speaker Set" (see page 99).
Control range: –10.0 dB to +10.0 dB
Initial setting: 0.0 dB
Control step: 0.5 dB
Speaker Level
Front L Front left speaker
Front R Front right speaker
Center Center speaker
Surround L Surround left speaker
Surround R Surround right speaker
Surround Back L Surround back left speaker
Surround Back R Surround back right speaker
Front Presence L Front presence left speaker
Front Presence R
Front presence right speaker
Rear presence left speaker
Rear Presence L
Rear Presence R
Rear presence right speaker
Subwoofer L Subwoofer left
Subwoofer R Subwoofer right
y
• If your subwoofer can adjust the output volume and the crossover
frequency, set the volume to about half way (or slightly less) and set the
crossover frequency to the maximum.
• If you use a handheld sound pressure level meter, hold at arm's length and
point upwards so that the meter is in the listening position. With the meter
set to the 70 dB scale and to C SLOW, calibrate each speaker to 75 dB.
Notes
• The available speaker channels differ depending on the setting of the
speakers.
• If you are only using one surround back speaker, connect it to the
SUR.BACK SINGLE jack, and adjust the balance in "Surround Back L".
• The setting of "Speaker Level" changes depending on the setting of "PEQ
Select" in "Manual Setup" (see page 104).
102
En
Adjusted speaker

Manual Setup (Volume)

Use this menu to manually adjust the various volume settings.
Adaptive DRC (Adaptive dynamic range control)
Use this feature to adjust the dynamic range in conjunction with the
volume level. This feature is useful when you are listening at lower
volumes or at night. When "Adaptive DRC" is set to "Auto", this
unit controls the dynamic range as follows:
– If the VOLUME setting is low: the dynamic range is narrow
– If the VOLUME setting is high: the dynamic range is wide
AUTO
OFF
Input level
VOLUME: low
Choice
Adjusts the dynamic range automatically.
Auto
Off
Does not adjust the dynamic range automatically.
y
• You can also adjust the dynamic range of the bitstream signal sources by
using "Dynamic Range" in "Sound" (see page 103).
• This function is also useful for listening with your headphones.
Notes
• The adaptive dynamic range control feature does not function when this
unit is in the THX Surround modes (see page 87) or Pure Direct mode (see
page 65).
• If you set "Direct" in "2ch Stereo" to "Auto" (see page 94) and this unit is
in the 2ch Stereo mode, the adaptive dynamic range control feature does
not function in some cases.
Adaptive DSP Lvl (Adaptive DSP effect level)
Use this feature to make fine adjustments of the DSP effect level
(see page 91) automatically in conjunction with the volume level.
Choice
Auto Adjusts the DSP effect level in conjunction with the
volume level.
Off Does not adjust the DSP effect level automatically.
Note
Even if you set "Adaptive DSP Lvl" to "Auto", this unit does not change but
fine-tunes the specified value of "DSP Level" (see page 91).
Max Volume (Maximum volume)
Use this feature to set the maximum volume level in the main zone.
This feature is useful to avoid the unexpected loud sound by mistake.
For example, the original volume range is –80.0 dB to +16.5 dB.
However, when "Max Volume" is set to –5.0 dB, the volume range
becomes –80.0 dB to –5.0 dB.
Control range: –30.0 dB to +15.0 dB, +16.5 dB
Control step: 5.0 dB
AUTO
OFF
Input level
VOLUME: high
Functions
Functions