Alarm contact output changeover setting (3 of mode selector 2)
This setting can be used to select
the alarm output logic N.C. or N.O.
contact.
ON : N.O.
OFF : N.C.
Output for external device setting (4 of mode selector 2)
This setting can be used to set the
output time of external output.
ON : Off-delay (2+30 sec.)
(When the sensor triggers an
alarm again during off-delay
time, the timer will be reset, and
the unit will continue to output
for another 30 seconds)
OFF : One-shot (2 sec.)
Short detection distance setting (5 of mode selector 2)
When the detection distance is
less than 66'(20m), set "ON".
ON : Enabled
OFF : Disabled
■Description of LED operation
■Alarm LED operation
・Lights up (for approx. 2 sec.) → When detecting intrusion (lights up for approx. 2 seconds simultaneously with alarm output)
・Continuously lit
・Blinks (for approx. 1 min.)...
・Continuously blinks (1)
・Continuously blinks (2)...
■Memory LED operation
・Blinks for 3 minutes, and then is lit for 47 minutes...
・Blinks for 50 minutes...
・Continuously blinks...
DIP switch 3
OFF
ON
N.C.
N.O.
(Factory set)
DIP switch 4
OFF
ON
One-shot
Off-delay
(Factory set)
DIP switch 5
OFF
ON
(Factory set)
→ Area checker position error (ends when the area checker position is reset)
(
Power voltage error (lights up after a power voltage error is detected, and ends when
power voltage returns to normal, or the power is reset)
0.5 sec.
0.5 sec.
0.5 sec.
→ During warming-up (blinks for approx. 1 minute after the power is turned ON)
0.15 sec. 0.15 sec.
0.15 sec. 0.15 sec.
0.1 sec.
0.6 sec.
0.1 sec.
(
→ Cover monitor error (starts blinking after opening the cover and closing it,
and ends when the sensor operates detection twice after
a lapse of 10 seconds)
Anti-masking error (start blinking when the anti-masking error is detected and
stops when the sensor operates detection twice after ten
seconds following recovery.)
0.15 sec.
0.15 sec.
0.85 sec.
→ Self diagnosis error (starts blinking when a self diagnosis error is detected, and ends when the unit is
normally recovered, or the power is reset)
0.25 sec. 0.25 sec.
0.25 sec. 0.25 sec.
→ When memory is indicated [auto reset operation: light goes off after blinking for 3 minutes, and then is lit
0.15 sec.
0.15 sec.
0.15 sec.
0.15 sec.
0.15 sec.
0.1 sec.
0.1 sec.
0.1 sec.
0.6 sec.
0.1 sec.
→ When memory is indicated [auto reset operation: light goes off after blinking for 50 minutes]
0.15 sec. 0.15 sec.
0.15 sec. 0.15 sec.
0.1 sec.
0.6 sec.
0.1 sec.
→ Cover monitor error (blinking for 10 seconds after opening the cover and closing it)
Anti-masking setting (7 of mode selector 2)
Enable / Disable the anti-masking
function.
ON :Enabled
OFF:Disabled
DIP Switch 1
OFF
1
2
3
4
5
6
7
8
* Keep the setting OFF in 6 , 8 of mode selector 2 for operation.
3 minutes
0.25 sec.
47 minutes
for 47 minutes] (retrigger enabled during lighting)
0.15 sec.
0.15 sec.
0.15 sec.
0.1 sec.
0.1 sec.
(retrigger enabled during lighting)
⑧
DIP Switch7
OFF
(Factory set)
Factory set
DIP Switch 2
ON
OFF
ON
1
2
3
4
5
6
7
8
Memory LED
: Red
Alarm LED
: Red
ON