Advertisement
Quick Links
Thank you for purchasing our photoelectric beam sensor.
This sensor will provide long and dependable service when properly installed.
Please read this Instruction Manual carefully for correct and effective use.
Please note : This sensor is designed to detect intrusion and to initiate an alarm ; it is not a burglary-preventing device.
TAKEX is not responsible for damage, injury or losses caused by accident, theft, Acts of God ( including inductive
surge by lightning ), abuse, misuse, abnormal usage, faulty installation or improper maintenance.
PRODUCT DESCRIPTION
The sensor contains a transmitter and receiver.
As illustrated, an infrared beam, projected by the
transmitter, is re ected back to the receiver.
The protection loop is formed along the path from the
transmitter to the re ector and back to the receiver.
When this protection loop is interrupted, the receiver will
initiate an alam.
＊As this sensor needs only one-side wiring, you can use it
in places where it's dif cult to wire on two sides.
＊Beam alignment can be adjusted at the sensor side only.
＊Pole attachment (option parts : BP-60A) is available for
both sensor and re ector.
＊L ttings (option parts : BL-11) is available for re ector
mounting.
1
PARTS DESCRIPTION
SENSOR
Terminals
Alarm LED
Lens
(Transmitter)
View finder
Lens
(Receiver)
COVER
REFLECTOR
ASSEMBLY
Reflectors
PHOTOELECTRIC BEAM SENSOR
PR-11BE : OUTDOOR 3.3 to 36ft. (1 to 11m)
: INDOOR
Instruction Manual
Reflector holder
3.3 to 49ft. (1 to 15m)
Transmitter
Receiver
Sensor
Attenuation
LED
Monitor jack
Response time
adjustment
Horizontal
adjustment
Vertical
adjustment
screw
MOUNTING PLATE
Hood
Reflector
unit
Self tapping
screw
φ4×30：2
Reflector mounting plate
ACCESSORY
(for outdoor) (for indoor)
Attenuation sheet : 2 pcs
OPTION PARTS
Self tapping
screw
Pole attachment
φ4×30：2
(BP-60A)
Pole mounting plate : 2 pcs
Pole bracket : 2 pcs
L fittings (BL-11)
Reflector
Advertisement
Related Manuals for Takex PR-11BE
Summary of Contents for Takex PR-11BE
-
Page 1: Product Description
Please note : This sensor is designed to detect intrusion and to initiate an alarm ; it is not a burglary-preventing device. TAKEX is not responsible for damage, injury or losses caused by accident, theft, Acts of God ( including inductive surge by lightning ), abuse, misuse, abnormal usage, faulty installation or improper maintenance. -
Page 2: Cautions On Installation
CAUTIONS ON INSTALLATION ・Do not install the ・Avoid strong light from the ・Do not install the unit ・Do not place highly ・Hazardous weather such ・Remove all sun, antomobile headlights etc. on places where it re ective objects as heavy rain or frost may obstructions (trees, unit on unsteady directly shining on sensor. -
Page 3: Installation
WIRING TERMINAL CONFIGULATION CONNECTION Control panel Example connection 1 (12VDC) ● ｝ ① ② ③ ④ ⑤ ⑥ ⑦ Power ｝ Alarm signal ①②③④ ＋ − Alarm ▼ When cover is detached ▼ Power 10.5V to 30VDC Tamper output Alarm output... -
Page 4: Pole Mount
・Reflector Assembly Self tapping screw ①Insert self tapping screws into the wall by about 0.79" 0.79" (20mm) (20mm) and hang the re ector unit back plate on them using the holes. Set the center of the re ector unit and minddle point of the sensor lenses at the same height, and you will nd it easier to adjust alignment. -
Page 5: Beam Alignment
ALIGNMENT AND OPERATION BEAM ALIGNMENT ①Face the sensor lenses to the re ector with its cover View finder View finder detached. Adjust the angle of the sensor unit vertically and horizontally by looking through the view nder placed between the sensor lenses. ①... -
Page 6: Troubleshooting
12 months from original date of shipment. During the Warranty Period, TAKEX will repair or replace, at its sole option, 0.59"(15mm) free of charge, any defective parts returned prepaid. Please provide the model number of the products, original date of shipment and nature of dif culty being experienced.