Pm4000 Mixing Console General Specifications - Yamaha PM4000 Operating Manual

PM4000 Mixing Console General Specifications

Total Harmonic Distortion
(Master Output)
Frequency Response (Master Output)
Hum & Noise (48 Channels)
(20 Hz - 20 kHz)
RS +
Input Gain = Max.
Input Pad = OFF
Input Sensitivity = -70 dB
Crosstalk
Maximum Voltage Gain
Channel Equalization
Channel High Pass Filter
Oscillator/Noise Generator
CH Preamp & EQ Peak Indicators
Channel LED Meter
Section 3.
Specifications
<0.1% (THD+N)
<0.01% (2nd - 10th harmonics)
0 ± dB
1/3
-128 dB
-100 dB
-85 dB (89 dB S/N)
-54 dB (58 dB S/N)
-84 dB (88 dB S/N)
-94 dB (98 dB S/N)
-80 dB @ 1 kHz, -70 dB @ 10 kHz
94 dB
104 dB
90 dB
100 dB
87 dB
84 dB
104 dB
84 dB
94 dB
91 dB
87 dB
90 dB
90 dB
87 dB
87 dB
84 dB
64 dB
0 dB
10 dB
10 dB
±15 dB maximum
12 dB/octave
Switchable sine wave @ 100 Hz,
1 kHz, 10 kHz or pink noise
Red LED
6 LEDs
Page 3-1
20 Hz - 20 kHz @ +14 dBu,
20 Hz - 20 kHz @ +14 dBu,
20 Hz - 20 kHz @ +4 dBu,
Equivalent Input Noise
Residual Output Noise
GROUP OUT Master fader at nominal level, all channel assign
switches OFF
GROUP OUT Master fader at nominal level, one channel fader at
nominal level
STEREO OUT Master fader at nominal level, all channel assign
switches OFF
MTRX OUT Master and Matrix mix controls at maximum level, all
GROUP to MTRX switches OFF
adjacent inputs or input to output
CH IN to GROUP OUT/STEREO OUT (CH to ST)/MTRX OUT
CH IN to stereo out (G to ST)
CH IN to AUX OUT (PRE)/AUX ST OUT (PRE, LVL)
CH IN to AUX OUT (POST)/AUX ST OUT (POST, LVL)
CH IN to AUX ST OUT (PRE, PAN)
CH IN to CH DIRECT OUT
CH IN to MONITOR OUT (GROUP to MONITOR)
CH IN MONITOR OUT (INPUT CUE)
ST IN (ST/L/R) to GROUP OUT
ST IN (L+R) to GROUP OUT
ST IN (ST/L/R) to AUX OUT (mono, PRE)
ST IN (L/R) to AUX OUT (mono, PRE)
ST IN (ST/L/R) to AUX ST OUT (stereo, PRE LVL)
ST IN (L+R) to AUX ST OUT (stereo, PRE LVL)
ST IN (ST/L/R) to AUX ST OUT (stereo, PRE BAL)
ST IN (L+R) to AUX ST OUT (stereo, PRE BAL)
TB IN to TB OUT
SUB IN (MTRX) to MTRX OUT
SUB IN (Others) to OUT (Others)
2TR IN to MONITOR OUT
HIGH 1k - 20 kHz (shelving/peaking, Q = 0.5 - 3)
HI-MID 0.4 k - 8 kHz (peaking; Q = 0.5 - 3)
LO-MID 80 - 1.6 kHz (peaking, Q = 0.5 - 3)
LOW 30 - 600 Hz (shelving/peaking, Q = 0.5 - 3)
Roll off below 20 - 400 Hz @ -3 dB points
Frequency sweepable at x0.2 - 2.0 nominal; less than 1% THD
at +4 dBu
Built into each input and stereo-in module; turns on when pre-EQ
level or post-EQ level reaches 3 dB below clipping
Level meter built into each monaural and stereo input module