Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for SMC Networks e-Rodless E-MY2 Series
Summary of Contents for SMC Networks e-Rodless E-MY2 Series
- Page 1 e-Rodless Actuator Operation Manual E-MY2 Series URL http://www.smcworld.com...
-
Page 2: Table Of Contents
CONTENTS Thank you for purchasing the SMC E-MY2 Series e-Rodless Actuator. Please read this manual carefully before operating the e-Rodless Actuator and make sure you understand the e-Rodless Actuator, SAFETY its capabilities and limitations. Please keep this manual handy for future reference. Model Indication Method Names and Functions of Individual Parts Installation... -
Page 3: Safety
SAFETY The e-Rodless Actuator and this manual contain essential information for the protection of users and others from possible injury and property damage and to ensure correct handling. Please check that you fully understand the definition of the following messages (signs) before Do not use the product in the environment with possible presence of flammable, going on to read the text, and always follow the instructions. -
Page 4: Model Indication Method
SAFETY (continue) Model Indication Method NOTE E-MY2 C 16 Follow the instructions given below when handling your actuator. Otherwise, the switch may be Number of Guide Type damaged or may fail, thereby resulting in malfunction. auto switches •Use at voltage over specified voltage. Cam follower guide type •Do not apply the load over max. -
Page 5: Names And Functions Of Individual Parts
Names and Functions of Individual Parts Installation Controller integrated type Read "Precautions for Handling" of safety Instruction and "How to install" of this chapter with care to provide safe and exact measurement for installation of the actuator. End side Motor Installation of body Controller I/O cable... - Page 6 Installation (continue) Installation of work Mounting controller (When controller separated type is used) Use 4 taps on the top of slider for installation of work. How to remove controller Motor Also, if necessary, utilize knock pin hole as well. Loosen M4 mounting screw shown in fig. 1 and remove the controller.
-
Page 7: Positions
Names and Functions of Controller (3 positions) 3 positions Controller detail E-MY2 C 16 Guide Type Number of auto switches Cam follower guide type State of indicator light Linear guide Auto switch single axis type light Linear guide Cable length goes out double axis type blink... - Page 8 Example of Internal Circuit and Wiring Electric Specification •Corresponding to NPN I/O Item Specification install power supply Power supply DC24V Power supply voltage switch cable Power supply Brown DC1 (+) for drive install power supply Current consumption Max.5A(within 2s) normally 2.5A at DC24V Blue DC1 (-) DC24V Power supply voltage...
-
Page 9: Setting
Setting Example of Internal Circuit and Wiring (continue) Signal through I/O cable Setting Procedures Input signal Confirm the product is installed and connected properly and perform setting in the following procedure. Symbol Command Command to operate motor side 1. troke adjustment Command to operate end side Command to operate intermediate stop means ON,... - Page 10 Setting (continue) 1.Stroke adjustment 3.Stroke learning Adjust the stroke of actuating part. 3-1 By push of over 3s at least, the product comes Slit into learning mode and starts stroke learning. Fixing bolt (2 pcs) 3-2 Confirm 2 indicator lamps MOTOR and END are lighting.
- Page 11 Setting (continue) Precautions on intermediate position 6.Setting of speed and acceleration Intermediate position is set relative to the motor side. 6-1 Setting of speed Therefore, if the stroke adjusting unit at the motor side is moved, the intermediate position is By adjustment of switch , the speed of changed.
-
Page 12: Operation Characteristics
Operation Characteristics Specifications Standard specifications Application of power supply Install power supply Item Specification When power supply is applied, the controller is initialized Model E-MY2C, E-MY2H, E-MY2HT READY output 2s or less and then READY output is performed. Low speed 10 to 1000 mm/s If first transit of used power supply is 1s or more, the Medium speed... -
Page 13: Positions
Names and Functions of Controller (5 positions) 5 positions Controller detail E-MY2 C 16 Guide Type Number of State of auto switches indicator light Cam follower guide type Linear guide Auto switch light single axis type goes out Linear guide Cable length blink double axis type... - Page 14 Example of Internal Circuit and Wiring Electric Specification •Corresponding to NPN I/O Item Specification install power supply Power supply DC24V Power supply voltage switch cable Power supply Brown DC1 (+) for drive install power supply Current consumption Max.5A(within 2s) normally 2.5A at DC24V Blue DC1 (-) DC24V Power supply voltage...
-
Page 15: Setting
Setting Example of Internal Circuit and Wiring (continue) Signal through I/O cable Setting Procedures Input signal Confirm the product is installed and connected properly and perform setting in the following procedure. Symbol Command Command to operate motor side 1. troke adjustment Command to operate end side Command to operate intermediate stop 1 Command to operate intermediate stop 2... - Page 16 Setting (continue) 1.Stroke adjustment 3.Stroke learning Adjust the stroke of actuating part. 3-1 By push of over 3s at least, the product comes into learning mode and starts stroke learning. Slit 3-2 Confirm 2 indicator lamps MOTOR and END are Fixing bolt (2 pcs) lighting.
- Page 17 Setting (continue) Precautions on intermediate position 6.Setting of speed and acceleration Intermediate position is set relative to the motor side. 6-1 Setting of speed Therefore, if the stroke adjusting unit at the motor side is moved, the intermediate position is By adjustment of switch , the speed of changed.
-
Page 18: Operation Characteristics
Operation Characteristics Application of power supply Intermediate operation READY output The input transmit drive command 1 When power supply is applied, the controller is initialized and then READY output is performed. Ex.)Movement from motor side to intermediate 1 The input transmit drive command 2 If first transit of used power supply is 1s or more, the alarm output is performed in prior The input transmit drive command 3 Do not turn off input of drive command until... -
Page 19: Specifications
Specifications Common Functions Standard specifications Lock function Item Specification If the set value of speed and acceleration need to be fixed, they can be locked. Set value of Model E-MY2C, E-MY2H, E-MY2HT intermediate position is not locked. Low speed 10 to 1000 mm/s Medium speed 50 to 1000 mm/s Transfer speed set range... -
Page 20: Alarm Indication And Remedy
Common Functions (continue) Alarm indication and remedy Perform the following remedy when an alarm comes out. Tuming off blink Ligting Point Display Content Disposition Point Display Content Disposition I f f o r e i g n m a t e r i a l i s Confirm the power supply f o u n d , r e m o v e i t a n d for signal is energized and... -
Page 21: Alarm Reset
Common Functions (continue) Alarm reset Alarm reset is available by manual alarm reset using and external alarm reset by external signal. (See page 36, 37 and after for ALM display in case of alarm.) Manual alarm reset When alarm occur, press for recovery from alarm condition.
Need help?
Do you have a question about the e-Rodless E-MY2 Series and is the answer not in the manual?
Questions and answers