Table of Contents
Advertisement
Quick Links
K&A MANUFACTURING
6703 ZINSER ST., SCHOFIELD, WI 54476
PHONE: 800.298.4351 FAX: 866.882.9475
www.raproducts.com
VERSION DATED: 8/5/13
READ ALL THE INSTRUCTIONS BEFORE BEGINNING.
DO NOT OPERATE THE UNIT UNTIL IT IS FULLY ASSEMBLED.
4
1
STEPS 1-3
INSTRUCTION # 52635
TOOLS REQUIRED FOR ASSEMBLY:
CORDLESS DRILL
#2 PHILLIPS HEAD DRIVER BIT OR
#2 SQUARE HEAD DRIVER BIT
7/32" HEX HEAD DRIVER BIT OR
ALLEN WRENCH (PROVIDED)
TAPE MEASURE
LEVEL
4
2
3
4
HARDWARE PACK # 52226 PLUS CENTER LEG BRACKET HARDWARE
NewCrank 3-LEG™ CRANK HEIGHT ADJUSTABLE WORKSTATION ASSEMBLY
INSTRUCTIONS:
STEP 1: LAY THE WORKSURFACE(S) 1 ON A PROTECTED SURFACE WITH THE
PILOT HOLES FACING UP. IF YOUR WORKSTATION HAS U-CHANNEL(S) 2 AND/
OR JOINER PLATE(S) 3 , ATTACH THEM AS FOLLOWS. IF NOT, PROCEED TO
STEP 4.
STEP 2: U-CHANNELS 2 ARE INCLUDED ON 72" AND LARGER WORKSTATIONS.
ALIGN THE HOLES IN THE U-CHANNEL(S) WITH THE PILOT HOLES IN THE WORK-
SURFACE(S) 1 . ATTACH THE U-CHANNEL(S) TO THE WORKSURFACE(S) WITH
(10) WOOD SCREWS 4 ON THE 42" U-CHANNEL OR (12) WOOD SCREWS ON
THE 54" U-CHANNEL. DO NOT OVER-TIGHTEN THE SCREWS. USE A LOW
TORQUE SETTING ON THE DRILL.
STEP 3: CENTER THE JOINER PLATE(S) 3 ON THE SEAM BETWEEN THE WORK-
SURFACES AND 3" FROM THE EDGES OF THE WORKSURFACES 1 . NO PILOT
HOLES ARE PROVIDED FOR THE JOINER PLATE(S). ATTACH THEM TO THE WORK-
SURFACES WITH (8) WOOD SCREWS 4 IN EACH JOINER PLATE.
YOU MAY HAVE (2) JOINER PLATES.
ITEM # PART #
1
VARIES WORKSURFACE(S)
2
VARIES 42" OR 54" U-CHANNEL
3
35UP 3x5 WORKSURFACE JOINER PLATE
4
51708 M5 x 18mm SQ/PH/WSHR HEAD WOOD SCREW
5
VARIES NewCrank COLUMN ASSY LH
6
VARIES NewCrank COLUMN ASSY 12" 3-LEGGED CENTER
7
VARIES NewCrank COLUMN ASSY RH
8
VARIES NewCrank HEX ROD
9
VARIES NewHeights 3-LEG CROSS SUPPORT BRACKET
10
52477 3/8 INTERIOR TOOTH STAR WASHER
11
52470 3/8-16 x 3/8 BUTTON HEAD SOCKET SCREW
12
VARIES NewHeightsCROSS SUPPORT 3-LEG
13
800411 NewHeights/HOVER END CAP
14
52498 7/32" ALLEN WRENCH
DESCRIPTION
QTY.
VARIES
VARIES
VARIES
VARIES
1
1
1
2
1
10
10
2
4
1
PAGE 1 OF 4
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for RightAngle NewCrank 3-LEG CRANK HEIGHT ADJUSTABLE WORKSTATION
Summary of Contents for RightAngle NewCrank 3-LEG CRANK HEIGHT ADJUSTABLE WORKSTATION
- Page 1 NewCrank 3-LEG™ CRANK HEIGHT ADJUSTABLE WORKSTATION ASSEMBLY TOOLS REQUIRED FOR ASSEMBLY: INSTRUCTIONS: CORDLESS DRILL #2 PHILLIPS HEAD DRIVER BIT OR STEP 1: LAY THE WORKSURFACE(S) 1 ON A PROTECTED SURFACE WITH THE #2 SQUARE HEAD DRIVER BIT K&A MANUFACTURING PILOT HOLES FACING UP. IF YOUR WORKSTATION HAS U-CHANNEL(S) 2 AND/ 7/32"...
- Page 2 STEP 4: PLACE THE CENTER COLUMN ASSEMBLY 6 ON THE WORKSURFACE ALIGNING THE HOLES IN THE WORK- SURFACE SUPPORT WITH THE PILOT HOLES IN THE WORKSURFACE. INSERT ONE OF THE (2) HEX RODS 8 INTO THE HEX DRIVE NEAR THE TOP OF THE COLUMN ASSEMBLY. PLACE THE LEFT COLUMN ASSEMBLY 5 ON THE WORK- SURFACE AND SLIDE IT TOWARD THE CENTER COLUMN ASSEMBLY INSERTING THE OTHER END OF THE HEX ROD K&A MANUFACTURING INTO THE HEX DRIVE NEAR THE TOP.
- Page 3 STEP 8: LEVEL THE CROSS SUPPORT 12 SO IT IS 4" FROM THE BOTTOM OF THE WORKSURFACE SUPPORT. SEE DETAIL C. FULLY TIGHTEN ALL THE SOCKET SCREWS. USE THE HEX HEAD DRIVER BIT OR THE ALLEN WRENCH PROVIDED 14 . INSERT AN END CAP 13 INTO EACH END OF THE CROSS SUPPORT.
- Page 4 TO CONVERT THE WORKSTATION FROM LEFT HANDED OPERATION TO RIGHT HANDED OPERATION FOLLOW THE INSTRUCTIONS BELOW: STEP 1: LOOSEN THE SCREW IN THE CLAMP B CLOSEST TO THE LEFT HAND COLUMN. PULL THE HEX ROD/CRANK K&A MANUFACTURING ASSEMBLY OUT OF THE CRANK HOLDER A TOWARD THE FRONT AND SET IT ASIDE FOR INSTALLATION ON THE RIGHT HAND COLUMN.
Need help?
Do you have a question about the NewCrank 3-LEG CRANK HEIGHT ADJUSTABLE WORKSTATION and is the answer not in the manual?
Questions and answers