Advertisement
Quick Links
Instruction # 53244
K&A Manufacturing
6703 Zinser Street
Schofield, WI 54476
Phone: 800.298.4351
Fax: 866.882.9475
www.raproducts.com
Version Dated: 7/11/16
NewHeights™ Series 4 NZP
Levante Crank Height
Adjustable Workstation
Read all the instructions before beginning.
Hardware Pack # 53243
Page1 OF 9
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for RightAngle NewHeights 4 NZP Series
Summary of Contents for RightAngle NewHeights 4 NZP Series
- Page 1 K&A Manufacturing 6703 Zinser Street Schofield, WI 54476 Phone: 800.298.4351 Fax: 866.882.9475 www.raproducts.com Version Dated: 7/11/16 NewHeights™ Series 4 NZP Levante Crank Height Adjustable Workstation Read all the instructions before beginning. Instruction # 53244 Hardware Pack # 53243 Page1 OF 9...
- Page 2 Tools Required for Assembly: Power Driver W/Adjustable Torque #2 Phillips Head Driver Bit #2 Square Head Driver Bit K&A Manufacturing 3/16" Hex Head Driver Bit or 6703 Zinser Street Schofield, WI 54476 Phone: 800.298.4351 Allen Wrench Fax: 866.882.9475 www.raproducts.com Tape Measure Level 51708 53013...
- Page 3 Costs incurred due to product replacement such as installation labor and transportation are not covered under this warranty. When corresponding with RightAngle™ products, provide the model and serial numbers located on one of the leg assemblies.
- Page 4 Step 1: Lay the worksurface 1 on a protected surface with the pilot holes facing up. Place the right leg assembly 3 on the worksurface aligning the holes in K&A Manufacturing 6703 Zinser Street Schofield, WI 54476 the worksurface support with the pilot holes in the Phone: 800.298.4351 Fax: 866.882.9475 worksurface.
- Page 5 Step 3: Slide the clamp 11 onto the hex rod protruding from the deflection gear 7 . Slide the bracket assembly 4 onto the hex rod aligning the holes in the K&A Manufacturing 6703 Zinser Street Schofield, WI 54476 bracket with the pilot holes in the worksurface 1 . Phone: 800.298.4351 Fax: 866.882.9475 Attach it with (4) wood screws 5 .
- Page 6 Step 5: Slide one end of the main drive tube 12 onto the gear drive on the deflection gear 7 . Place K&A Manufacturing the left leg assembly 2 on the worksurface 1 guiding 6703 Zinser Street Schofield, WI 54476 the other end of the drive tube into the gear drive Phone: 800.298.4351 Fax: 866.882.9475...
- Page 7 Step 6: With the help of an assistant align the cross support 15 with the stickers on both leg assemblies. See below. Insert (4) socket screws 13 through the holes in the ends of the cross support and thread them into the weld nuts that are held in place by the stickers.
- Page 8 Step 8: Fully tighten the (8) screws 5 holding the leg assemblies 2 & 3 to the worksurface 1 . Drive K&A Manufacturing (8) more wood screws through the worksurface 6703 Zinser Street Schofield, WI 54476 support and into the worksurface. Fully tighten. Phone: 800.298.4351 Fax: 866.882.9475 www.raproducts.com...
- Page 9 Instructions To Install a Track on a Series 4 Workstation: K&A Manufacturing Step 1: Place the front of the track A against the 6703 Zinser Street Schofield, WI 54476 bottom of the worksurface and the back of the track Phone: 800.298.4351 Fax: 866.882.9475 on the angled part of the u-channel.
Need help?
Do you have a question about the NewHeights 4 NZP Series and is the answer not in the manual?
Questions and answers