RightAngle NewHeights SPLIT WORKSURFACE ELECTRIC HEIGHT ADJUSTABLE WORKSTATION Assembly Instructions

K&A MANUFACTURING
6703 ZINSER ST., SCHOFIELD, WI 54476
PHONE: 800.298.4351 FAX: 866.882.9475
www.raproducts.com
VERSION DATED: 7/18/12
PRE-INSTALLED
T-SLOT PLATE
DETAIL A
4
STEPS 1-5
6
INSTRUCTION # 52598
TOOLS REQUIRED FOR ASSEMBLY:
CORDLESS DRILL
#2 PHILLIPS HEAD DRIVER BIT OR
#2 SQUARE HEAD DRIVER BIT
4mm HEX HEAD DRIVER BIT OR
ALLEN WRENCH PROVIDED
TAPE MEASURE
LEVEL
BOTTOM OF
WORKSURFACE
SUPPORT
2
LOCATING THE CROSS SUPPORT
(SEE EXCEPTION IN STEP 4)
FOOT
8
WORKSURFACE
SUPPORT
1
MOTOR
WIRES
5 7
NewHeights SPLIT WORKSURFACE ELECTRIC HEIGHT ADJUSTABLE WORKSTATION
ASSEMBLY INSTRUCTIONS:
STEP 1: LAY THE FIXED WORKSURFACE 1 ON A PROTECTED SURFACE WITH
THE PILOT HOLES FACING UP.
STEP 2: PLACE THE LEFT HAND COLUMN ASSEMBLY 2
COLUMN ASSEMBLY 3
WIRES MUST FACE THE INSIDE OF THE WORKSTATION. ALIGN THE HOLES IN THE
WORKSURFACE SUPPORTS WITH THE PILOT HOLES IN THE WORKSURFACE.
STEP 3: WITH THE HELP OF AN ASSISTANT, PLACE (4) STAR WASHERS 5
SOCKET SCREWS 6 . INSERT THESE THROUGH THE HOLES AT THE ENDS OF THE
CROSS SUPPORT
INSTALLED IN THE SLOTS IN THE COLUMN ASSEMBLIES 2
AT LEFT. DO NOT FULLY TIGHTEN.
STEP 4: LEVEL THE CROSS SUPPORT 4 AT 4" FROM THE BOTTOM OF THE WORK-
SURFACE SUPPORT AND FULLY TIGHTEN THE SOCKET SCREWS
DETAIL AT LEFT. SPECIAL EXCEPTION: ON WORKSTATIONS ON WHICH THE
LifeBalance STATION IS BEING INSTALLED, THE CROSS SUPPORT SHOULD BE
4.00
INSTALLED RESTING ON THE FEET OF THE COLUMN ASSEMBLIES TO ALLOW FOR
CLEARANCE OF THE EQUIPMENT. INSERT (2) END CAPS 7
THE CROSS SUPPORT.
STEP 5: ALIGN THE HOLES IN THE WORKSURFACE SUPPORTS WITH THE PILOT
HOLES IN THE WORKSURFACE
TO THE WORKSURFACE USING (16) WOOD SCREWS
TIGHTEN THE SCREWS. USE A LOW TORQUE SETTING ON THE DRILL.
3
ITEM # PART #
1 VARIES NewHeights FIXED WORKSURFACE
2 VARIES NewHeights LEFT HAND COLUMN ASSEMBLY
3 VARIES NewHeights RIGHT HAND COLUMN ASSEMBLY
4 VARIES NewHeights CROSS SUPPORT
5 52477 3/8 INTERIOR TOOTH STAR WASHER
6 52470 3/8-16 x 3/8 BUTTON HEAD SOCKET SCREW
7 800411 NewHeights/HOVER END CAP
8 51708 M5 x 18mm SQ/PH/WSHR HEAD WOOD SCREW
9 VARIES NewHeights MOVABLE WORKSURFACE
10 50219 NewHeights SWING ARM (300SW)
11 50072 8 x 3/4 PHILLIPS PAN HEAD RECEX DRIVE SCREW
12 51951 WIRE MANAGEMENT J
13 50298 NewHeights CONTROL BOX
14 50285 NewHeights HAND SWITCH
15 52498 7/32" ALLEN WRENCH
HARDWARE QUANTITIES MAY VARY
HARDWARE PACK # 52226
ON THE WORKSURFACE 1 AS SHOWN. THE MOTOR
4 AND THREAD THEM INTO THE T-SLOT PLATES THAT ARE PRE-
1 . ATTACH THE WORKSURFACE SUPPORTS
DESCRIPTION
AND THE RIGHT HAND
ON (4)
AND 3 . SEE DETAIL A
6 . SEE THE
INTO THE ENDS OF
8 . DO NOT OVER-
QTY.
1
1
1
1
4
4
2
19
1
1
4
3
1
1
1
PAGE 1 OF 3