Related Manuals for Nexo PSR2 Series
Summary of Contents for Nexo PSR2 Series
- Page 1 DP2538-05-CM PSR2 Series PS8 & LS400 PS10R2 & LS600 PS15R2 & LS18 System manual System Manual PSR2 Series...
-
Page 2: Table Of Contents
..........................38 NSTALLATION APPLICATIONS 6.3.1 Described configurations ............................... 38 6.3.2 PS rigidly mounted on a wall or a ceiling (vertical or horizontal) ............39 6.3.3 PS10R2/PS15R2/LS600 mounted on a ceiling (vertical) ................41 Page 2 / 109 System Manual PSR2 Series... - Page 3 8.7.10 GPI-ANPL1 ................................. 87 8.7.11 GPI-ANPL3 ................................. 88 8.7.12 LSI-CPLA ..................................89 8.7.13 VNI-IPCOV8 ................................90 8.7.14 VNI-IPCOV15 ................................91 8.7.15 VNT-ADPT .................................. 92 8.7.16 VNT-SSBRK8 ................................93 8.7.17 VNT-SSBRK10 ................................94 Page 3 / 109 System Manual PSR2 Series...
- Page 4 LST-XBOW18 ................................. 100 8.7.24 VXT-BL820................................101 8.7.26 GPT-GSTK ................................102 8.7.27 LST-COVER18 ................................ 103 8.7.28 LST-WB18 ................................104 PS & LS MODULES & ACCESSORIES LIST ..................105 10 USER NOTES ............................108 Page 4 / 109 System Manual PSR2 Series...
-
Page 5: Please Read Carefully Before Proceeding
User Manual. Failure to do this exposes people to potential injury or death. Please check the web site nexo-sa.com for the latest update. Always consult qualified NEXO personnel if the device installation requires construction work and make sure to observe the following precautions: Mounting precautions choose mounting hardware and an installation location that can support 4 times the weight of the speaker system;... - Page 6 The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. Page 6 / 109 System Manual PSR2 Series...
-
Page 7: Introduction
NEXO web site (nexo-sa.com) for the latest software releases. • NS-1 simulation software assists in the design and implementation of PS Series. Please consult the NEXO web site (nexo-sa.com) for the latest software releases. • Available for Mac, iPad and iPhone, NEXO NeMo provides full remote control over a digital audio network from anywhere in the venue, thanks to an intuitive and graphically attractive user interface. -
Page 8: Ps And Ls General Setup Instructions
PS15R2 LF (+) 2(-) PS15R2 (-) PS15R2 HF (-) 2(+) PS15R2 (+) PS15R2 HF (+) 2.1.3 LS subwoofers connectors Speakon Connector 1(-) LS (-) 1(+) LS (+) 2(-) Through Through 2(+) Page 8 / 109 System Manual PSR2 Series... -
Page 9: Configuring Ps15R2 For Passive Or Active Mode
Active mode Cabling NEXO recommends the exclusive use of multi-conductor cables to connect the system: the cable kit is compatible with all the cabinets, and there is no possible confusion between LF, MF and HF sections. Cable choice consists mainly of selecting cables of the correct sectional dimension (size) in relation to the load resistance and the cable length. -
Page 10: Ps And Ls Recommended Amplification
4 x PS15R2 in passive mode per channel 4 x PS15R2 in active mode: 2 channels 3 x LS18 per channel PS and LS setups on NEXO TD Controllers Please consult nexo-sa.com for NEXO TD Controllers firmware information. Page 10 / 109 System Manual PSR2 Series... -
Page 11: Connection Diagrams
CONNECTION DIAGRAMS ONNECTION DIAGRAMS PS8 and LS400 / DTDAMP4x1.3 PS10R2 and LS600 / DTDAMP4x1.3 Page 11 / 109 System Manual PSR2 Series... -
Page 12: Ps15R2 (Passive Mode) And Ls18 / Dtdamp4X1.3 (Bridge Stereo)
CONNECTION DIAGRAMS PS15R2 (passive mode) and LS18 / DTDAMP4x1.3 (Bridge Stereo) Page 12 / 109 System Manual PSR2 Series... -
Page 13: Mk 2 (4 Channels Mode )
CONNECTION DIAGRAMS PS8 / NXAMP4x1mk2 (4 channels mode) Page 13 / 109 System Manual PSR2 Series... -
Page 14: Channels Mode )
CONNECTION DIAGRAMS LS400 / NXAMP4x1mk2 (4 channels mode) Page 14 / 109 System Manual PSR2 Series... - Page 15 CONNECTION DIAGRAMS PS8 and LS400 / NXAMP4x1mk2 (4 channels mode) Page 15 / 109 System Manual PSR2 Series...
-
Page 16: Ps10R2 And Ls600 / Nxamp4 Mk Ridge Tereo )
CONNECTION DIAGRAMS PS10R2 and LS600 / NXAMP4x1mk2 (Bridge Stereo) PS15R2 (passive mode) and LS18 / NXAMP4x1mk2 (Bridge Stereo) Page 16 / 109 System Manual PSR2 Series... -
Page 17: Channels Mode )
CONNECTION DIAGRAMS PS8 and LS400 / NXAMP4x2mk2 (4 channels mode) Page 17 / 109 System Manual PSR2 Series... -
Page 18: Ps10R2 / Nxamp4 Mk Channels Mode )
CONNECTION DIAGRAMS 3.10 PS10R2 / NXAMP4x2mk2 (4 channels mode) Page 18 / 109 System Manual PSR2 Series... -
Page 19: Channels Mode )
CONNECTION DIAGRAMS 3.11 LS600 / NXAMP4x2mk2 (4 channels mode) Page 19 / 109 System Manual PSR2 Series... -
Page 20: Channels Mode )
CONNECTION DIAGRAMS 3.12 PS10R2 and LS600 / NXAMP4x2mk2 (4 channels mode) Page 20 / 109 System Manual PSR2 Series... -
Page 21: Channels Mode )
CONNECTION DIAGRAMS 3.13 PS15R2 (passive mode) and LS18 / NXAMP4x2mk2 (4 channels mode) Page 21 / 109 System Manual PSR2 Series... -
Page 22: Channels Mode )
CONNECTION DIAGRAMS 3.14 PS8 and LS400 / NXAMP4x4mk2 (4 channels mode) Page 22 / 109 System Manual PSR2 Series... -
Page 23: Channels Mode )
CONNECTION DIAGRAMS 3.15 PS10R2 and LS600 / NXAMP4x4mk2 (4 channels mode) Page 23 / 109 System Manual PSR2 Series... -
Page 24: Channels Mode )
CONNECTION DIAGRAMS 3.16 PS15R2 (passive mode) / NXAMP4x4mk2 (4 channels mode) Page 24 / 109 System Manual PSR2 Series... -
Page 25: Ps15R2 ( Active Mode ) / Nxamp4
CONNECTION DIAGRAMS 3.17 PS15R2 (active mode) / NXAMP4x4mk2 (4 channels mode) Page 25 / 109 System Manual PSR2 Series... -
Page 26: Ls18 Omni Mode / Nxamp4
CONNECTION DIAGRAMS 3.18 LS18 Omni Mode / NXAMP4x4mk2 (4 channels mode) Page 26 / 109 System Manual PSR2 Series... -
Page 27: Ls18 Cardio Mode / Nxamp4
CONNECTION DIAGRAMS 3.19 LS18 Cardio Mode / NXAMP4x4mk2 (4 channels mode) Page 27 / 109 System Manual PSR2 Series... -
Page 28: Ps15R2 ( Passive Mode And Ls18 / Nxamp4 Mk Channels Mode )
CONNECTION DIAGRAMS 3.20 PS15R2 (passive mode) and LS18 / NXAMP4x4mk2 (4 channels mode) Page 28 / 109 System Manual PSR2 Series... -
Page 29: Simulation Software
Help section): dimensions, weight, gravity centre position, forces, moments, working load and safety factor. PS and LS Structural Analysis Report is certified by German Certification Organization RWTUV systems GmbH. NS-1 installation package includes all NEXO User Manuals, Structural Analysis Reports and Certificates PDF files. NS-1 is a freeware available on nexo-sa.com... -
Page 30: Configurable Asymetrical Horn
A sticker on the wide dispersion side of the horn shows the correct orientation for wedge monitoring and front of house applications: you simply position the indication on the desired side. The arrow indicates the wide dispersion. Page 30 / 109 System Manual PSR2 Series... -
Page 31: Front Of House" Configuration
(below the horn axis). For floor monitor use the horn must be rotated with its "wide" dispersion side directed towards the top of the cabinet (as shown by the arrow) in wedge position as shown in the above figure. Page 31 / 109 System Manual PSR2 Series... -
Page 32: Ps Series Hardware Setup Procedure
For fixed installations, wind loading has to be taken into account in accordance to the national standards. The PS and LS Rigging System requires regular inspection and testing by a competent test centre. NEXO recommend that the system is load tested and certified annually or more frequently if local regulations require. -
Page 33: Ground Stacking Safety
Be aware that safety procedures are as important in the truck and in the warehouse as they are at the venue. 6.1.3 Contacts Correct training is fundamental to safe practise when working with loudspeakers flying systems. NEXO recommend that users contact local industry associations for information on specialist course. Information for International training agencies can be obtained by contacting either:... -
Page 34: General Description
LS18 connecting plates There are two families of accessories: fixed installation accessories, which are designed to be screwed on the connecting plates touring accessories, which can be installed or removed with quick connecting systems Page 34 / 109 System Manual PSR2 Series... -
Page 35: Accessories
PS SERIES HARDWARE SETUP PROCEDURE 6.2.3 Accessories PS and LS accessories are: VNI-UBRK8 VNI-UBRK10 VNI-UBR VNI-ABRK VNI-LBRK VNI-WS8 VNI-WS10 VNI-WS15 GPI-BUMPER GPI-ANPL1 GPI-ANPL3 LSI-CPLA VNI-IPCOV8 VNI-IPCOV15 VNT-ADPT VNT-SSBRK8 VNT-SSBRK10 VNT-SSBRK15 VNT- TCBRK VNT-XHBRK VNT- TTC Page 35 / 109 System Manual PSR2 Series... - Page 36 PS SERIES HARDWARE SETUP PROCEDURE GPT- BUMPER LST-XBOW18 VXT-BL820 GPT-GSTK LST-COVER18 LST-WB18 Page 36 / 109 System Manual PSR2 Series...
-
Page 37: Warnings On Ps And Ls Accessories
Never use other accessories – including push-pins - when assembling PS and LS cabinets than the ones provided by NEXO: NEXO will decline responsibility over the entire PS and LS accessory range if any component is purchased from different supplier. -
Page 38: Installation Applications
LOCTITE 243 or equivalent for all screws used with PS and LS fixed installation accessories. LOCTITE 243 is available at NEXO or at your local distributor upon request. Page 38 / 109 System Manual PSR2 Series... -
Page 39: Ps Rigidly Mounted On A Wall Or A Ceiling (Vertical Or Horizontal)
Position the PS inside the “U” Bracket to desired angle; “U” bracket oblong holes must be properly aligned with panels holes Use the screws and washers from VNI-UBRK kit to connect “U” bracket to cabinet “U” BRACKET MOUNTING PROCEDURE FOR PS8 Page 39 / 109 System Manual PSR2 Series... - Page 40 PS SERIES HARDWARE SETUP PROCEDURE “U” BRACKET MOUNTING PROCEDURE FOR PS10R2 “U” BRACKET MOUNTING PROCEDURE FOR PS15R2 Page 40 / 109 System Manual PSR2 Series...
-
Page 41: Ps10R2/Ps15R2/Ls600 Mounted On A Ceiling (Vertical)
Position bracket from VNI-LBRK kit, or VNI-ABRK and secure it to the cabinet using the 2 remaining shoulder screws supplied with this kit. Slings and shackles (not provided) are required to secure the cluster under the ceiling Page 41 / 109 System Manual PSR2 Series... -
Page 42: Ps15R2 Mounted On A Ceiling (Horizontalal)
Position “L” brackets from VNI-LBRK kits and secure them to the cabinet using the 4 remaining shoulder screws supplied with these kits Slings and shackles (not provided) are required to secure the speaker under the ceiling CABLE SUSPENSION MOUNTING PROCEDURE FOR PS15R2 Page 42 / 109 System Manual PSR2 Series... -
Page 43: Ps And Ls600 Wall Suspension (Vertical)
Position the srews in the oblong hole so that required vertical angle is obtained (no tilt with LS600) Secure the screws Suspend and secure the cabinet to the wall suspension Adjust horizontal angle WALL SUSPENSION PROCEDURE FOR VERTICAL INSTALLATION Page 43 / 109 System Manual PSR2 Series... -
Page 44: Ps8/Ps10R2 Wall Suspension (Horizontal)
Connect the "U" bracket to the connector plate by using the screws provided with the VNI-WS kit Secure the screws Suspend and secure the cabinet to the wall suspension Adjust horizontal angle WALL SUSPENSION PROCEDURE FOR HORIZONTAL INSTALLATION Page 44 / 109 System Manual PSR2 Series... -
Page 45: Ls18 And Ps15R2 Vertical Array Rigidly Mounted On A Ceiling
Position GPI-ANPL3 angle plate (set at 16°) and LSI-CPLA top counter-plates on LS18 upper sides according to figure below right Use thread lock coated screws (if not apply Loctite 243 or equivalent to shoulder screws) from LSI-CPLA and GPI-ANPL kits Page 45 / 109 System Manual PSR2 Series... - Page 46 Flip cluster by 90° so that it is ready to be positioned under the ceiling Four screws 12mm diameter (not provided) are required to secure the bumper under the ceiling Page 46 / 109 System Manual PSR2 Series...
-
Page 47: Ls18 And Ps15R2 Vertical Array Cable Mounted On A Ceiling
Connect the bumper and the two “L” brackets using the screws, washers and bolts provided in the VNI-LBRK kit Proceed as in preceding sections 4 slings and 4 shackles (not provided) are required to secure the cluster under the ceiling Page 47 / 109 System Manual PSR2 Series... -
Page 48: Touring Applications
PS SERIES HARDWARE SETUP PROCEDURE Touring applications 6.4.1 Described configurations SECTION 6.4.4 SECTION 6.4.3 SECTION 6.4.2 SECTION 6.4.6 SECTION 6.4.5 Page 48 / 109 System Manual PSR2 Series... -
Page 49: Ps On Speaker Stand Or On Ls Subwoofer
R>H IMPORTANT NEXO PLSTD pole stand only should be used for mounting on top of NEXO LS LS must always be installed on a horizontal surface Ensure that public is not allowed within a safety area which radius is equal or higher than assembly height... -
Page 50: Ps Flown Vertically
243 or equivalent for the two screws securing the PS8 flying adaptor. LOCTITE 243 is available at NEXO or at your local distributor upon request. PS8 FLYING ADAPTOR INSTALLATION Slide flying bar VNT-TTC into PS connecting plate or adaptor oblong holes... - Page 51 PS SERIES HARDWARE SETUP PROCEDURE PS SERIES VERTICAL SUSPENSION PROCEDURE Page 51 / 109 System Manual PSR2 Series...
-
Page 52: Ps Flown Horizontally
243 or equivalent the two screws securing the PS8 flying adaptor. LOCTITE 243 is available at NEXO or at your local distributor upon request. PS8 FLYING ADAPTOR INSTALLATION Insert male pole side of bracket into PS cabinet Fold the opposite bar of the bracket until it is locked at 90° (a “click” from the locker will ensure proper locking) - Page 53 PS SERIES HORIZONTAL SUSPENSION PROCEDURE Unlocking the "U" bracket safety locker: Lift the metal plate located at the corner of the bracket and unfold the side bar UNLOCKING "U“ BRACKET SAFETY LOCKER Page 53 / 109 System Manual PSR2 Series...
-
Page 54: Ls18 Flown Vertically
Please check NS-1 for mechanical Safety Working Load computations. IMPORTANT Please check configuration in NS-1 for proper motor hoist rating Procedure Insert LST-XBOW into connecting plates of both sides of LS18s LS18 XBOW ANGLE SETTINGS PLATE Page 54 / 109 System Manual PSR2 Series... - Page 55 Ensure that all quick release pins are properly locked into their position. Lift cluster to NS-1 defined rigging height, secure cluster horizontally to prevent it from rotating Secure bumper with secondary safety steel Page 55 / 109 System Manual PSR2 Series...
- Page 56 PS SERIES HARDWARE SETUP PROCEDURE IMPORTANT The requirements for secondary safety systems vary with territories. However, the secondary safety steel MUST have a SWL equivalent or greater than that of the rigging system. Page 56 / 109 System Manual PSR2 Series...
-
Page 57: Ground Stacked Ls18
Assemble the two connecting beam and the reinforcement beam with the handles Depending on tilt angle – negative, null or positive - to be achieved, there are three positions to connect above assembly to the supporting beams; below drawings detail these configurations: Page 57 / 109 System Manual PSR2 Series... - Page 58 Connect bottom LS18 to GPT-GSTK Ground stacking device with 4 VXT-BL820 quick release pins Connect second LS18 with X-Bow front articulation holes and rear link bars and ensure quick release pins are properly locked Repeat above steps for subsequent cabinets Page 58 / 109 System Manual PSR2 Series...
- Page 59 PS SERIES HARDWARE SETUP PROCEDURE Page 59 / 109 System Manual PSR2 Series...
-
Page 60: Testing And Maintenance Of The System
After cleaning, the rigging system must be treated with a suitable lubricant to prevent rusting. NEXO recommends the use of Scottoil FS365 which is a water-based lubricant with a mixture of machine oil, surfactant and anti-rust treatment. -
Page 61: System Check Alignment Guidelines
SYSTEM CHECK ALIGNMENT GUIDELINES The NEXO TD Controllers factory delay presets are optimised to provide the best possible crossover between the PS and LS systems. The reference point for this adjustment is the front of each cabinet. (This means that the internal delays needed to achieve a correct time alignment are set for cabinets standing next to each other with both fronts aligned). -
Page 62: Driving The Ls From The Aux Send
By doing so, drivers are working perfectly together and providing the best efficiency possible. It is then up to the user to adjust the delay on the NEXO TD Controllers to match the physical path difference of the different systems. It is thus possible to get a well-adjusted system, even without measuring instruments. -
Page 63: Technical Specifications
TECHNICAL SPECIFICATIONS ECHNICAL PECIFICATIONS LS18 and LS18-E 8.1.1 System specifications LS18 WITH NEXO TDCONTROLLER SETUP Frequency Response @-6 dB 32 Hz to 130 Hz Sensitivity 1W@1m 107 dB SPL Nominal Peak SPL@1m 137 to 140 dB Available Crossover Frequencies 35-60, 35-85, 35-120 Hz... -
Page 64: Dimensions (Mm/Inches)
TECHNICAL SPECIFICATIONS 8.1.2 Dimensions (mm/inches) Page 64 / 109 System Manual PSR2 Series... -
Page 65: System Specifications
TECHNICAL SPECIFICATIONS LS600 8.2.1 System specifications LS600 WITH NEXO TDCONTROLLER SETUP Frequency Response @-6 dB 38 Hz to 120 Hz Sensitivity 1W@1m 101 dB SPL Nominal Peak SPL@1m 135 to 138 dB Available Crossover Frequencies 40-85, 40-120, 60-120 Hz Nominal Impedance... -
Page 66: Dimensions (Mm/Inches)
TECHNICAL SPECIFICATIONS 8.2.2 Dimensions (mm/inches) Page 66 / 109 System Manual PSR2 Series... -
Page 67: System Specifications
TECHNICAL SPECIFICATIONS LS400 8.3.1 System specifications LS400 WITH NEXO TDCONTROLLER SETUP Frequency Response @-6 dB 40 Hz to 140 Hz Sensitivity 1W@1m 99 dB SPL Nominal Peak SPL@1m 128 to 131 dB Available Crossover Frequencies 40-85, 40-120, 60-120 Hz Nominal Impedance... -
Page 68: Dimensions (Mm/Inches)
TECHNICAL SPECIFICATIONS 8.3.2 Dimensions (mm/inches) Page 68 / 109 System Manual PSR2 Series... -
Page 69: Ps15R2
TECHNICAL SPECIFICATIONS PS15R2 8.4.1 System specifications PS15R2 WITH NEXO TDCONTROLLER SETUP Frequency Response @-6 dB 47 Hz to 18 kHz Sensitivity 1W@1m 102 dB SPL Nominal Peak SPL@1m 133 to 136 dB 50° to 100° Horizontal – 55° Vertical Rotatable Horn... -
Page 70: Dimensions (Mm/Inches)
TECHNICAL SPECIFICATIONS 8.4.2 Dimensions (mm/inches) Page 70 / 109 System Manual PSR2 Series... -
Page 71: Diagrams
Impedance RS15 – 1 channel - (grey) & PS15R2 (black) On-axis response RS15 (grey) & PS15R2 (black) Horizontal plane coverage, vertical orientation +25° Horizontal plane coverage, vertical orientation 0° Horizontal plane coverage, vertical orientation -25° Vertical plane coverage Page 71 / 109 System Manual PSR2 Series... -
Page 72: Ps10R2
TECHNICAL SPECIFICATIONS PS10R2 8.5.1 System specifications PS10R2 WITH NEXO TDCONTROLLER SETUP Frequency Response @-6 dB 58 Hz to 20 kHz Sensitivity 1W@1m 99 dB SPL Nominal Peak SPL@1m 129 to 132 dB 50° to 100° Horizontal – 55° Vertical Rotatable Horn... -
Page 73: Dimensions (Mm/Inches)
TECHNICAL SPECIFICATIONS 8.5.2 Dimensions (mm/inches) Page 73 / 109 System Manual PSR2 Series... -
Page 74: Diagrams
On-axis response LS600 (grey) & PS10R2 (black) Impedance LS600 (grey) & PS10R2 (black) Horizontal plane coverage, vertical orientation +25° Horizontal plane coverage, vertical orientation 0° Horizontal plane coverage, vertical orientation -25° Vertical plane coverage Page 74 / 109 System Manual PSR2 Series... -
Page 75: System Specifications
TECHNICAL SPECIFICATIONS 8.6.1 System specifications PS8 WITH NEXO TDCONTROLLER SETUP Frequency Response @-6 dB 62 Hz to 20 kHz Sensitivity 1W@1m 96 dB SPL Nominal Peak SPL@1m 122 to 125 dB 50° to 100° Horizontal – 55° Vertical Rotatable Horn... -
Page 76: Dimensions (Mm/Inches)
TECHNICAL SPECIFICATIONS 8.6.2 Dimensions (mm/inches) Page 76 / 109 System Manual PSR2 Series... -
Page 77: Diagrams
On-axis response LS400 (grey) & PS8 (black) Impedance LS400 (grey) & PS8 (black) Horizontal plane coverage, vertical orientation +25° Horizontal plane coverage, vertical orientation 0° Horizontal plane coverage, vertical orientation -25° Vertical plane coverage Page 77 / 109 System Manual PSR2 Series... -
Page 78: Ps And Ls Accessories
TECHNICAL SPECIFICATIONS PS and LS accessories 8.7.1 VNI-UBRK8 Parts X3 (M5x25) X3 (M5) Dimensions Weight: 2.4 kg / 5.3 lb Page 78 / 109 System Manual PSR2 Series... -
Page 79: Vni-Ubrk10
TECHNICAL SPECIFICATIONS 8.7.2 VNI-UBRK10 Parts M6x20 M10x20 M8x45 Dimensions Weight: 2.5 kg / 5.5 lb Page 79 / 109 System Manual PSR2 Series... -
Page 80: Vni-Ubrk12
TECHNICAL SPECIFICATIONS 8.7.3 VNI-UBRK12 Parts Dimensions Weight: 6 kg / 13 lb Page 80 / 109 System Manual PSR2 Series... -
Page 81: Vni-Abrk
TECHNICAL SPECIFICATIONS VNI-ABRK 8.7.4 Parts X2 (D8x12) X2 (D8x20) X2 (M8) X2 (M6x25) X2 (M6) X2 (M12x35) X2 (M12) X2 (M12) Dimensions Weight: 1 kg / 2.2 lb Page 81 / 109 System Manual PSR2 Series... -
Page 82: Vni-Lbrk
TECHNICAL SPECIFICATIONS 8.7.5 VNI-LBRK Parts X2 (D8x12) X2 (D8x20) X2 (M8) X2 (M6x25) X2 (M6) X2 (M12x35) X4 (M12) X2 (M12) Dimensions 11,9 Weight: 1.6 kg / 3.5 lb Page 82 / 109 System Manual PSR2 Series... -
Page 83: Vni-Ws8
TECHNICAL SPECIFICATIONS 8.7.6 VNI-WS8 Parts X1 (Arm) X1 (Adapter) Dimensions Weight: 1.2 kg / 2.7 lb Page 83 / 109 System Manual PSR2 Series... -
Page 84: Vni-Ws10
TECHNICAL SPECIFICATIONS 8.7.7 VNI-WS10 Parts X1 (Arm) X1 (Adapter) Dimensions Weight: 1.35 kg / 3 lb Page 84 / 109 System Manual PSR2 Series... -
Page 85: Vni-Ws15
TECHNICAL SPECIFICATIONS 8.7.8 VNI-WS15 Parts X1 (Arm) X1 (Adapter) Dimensions Weight: 2.8 kg / 6.2 lb Page 85 / 109 System Manual PSR2 Series... -
Page 86: Gpi-Bumper
TECHNICAL SPECIFICATIONS 8.7.9 GPI-BUMPER Parts X8 (D8x20 M6) Dimensions 27,2 Weight: 14.5 kg / 32 lb Page 86 / 109 System Manual PSR2 Series... -
Page 87: Gpi-Anpl1
TECHNICAL SPECIFICATIONS 8.7.10 GPI-ANPL1 Parts X8 (D8x20 M6) Dimensions 12,3 Weight: 8 kg / 17.6 lb Page 87 / 109 System Manual PSR2 Series... -
Page 88: Gpi-Anpl3
TECHNICAL SPECIFICATIONS 8.7.11 GPI-ANPL3 Parts X8 (D8x20 M6) Dimensions 11,5 Weight: 6.6 kg / 14.6 lb Page 88 / 109 System Manual PSR2 Series... -
Page 89: Lsi-Cpla
TECHNICAL SPECIFICATIONS 8.7.12 LSI-CPLA Parts X8 (D8x20 M6) Dimensions Weight: 2.5 kg / 5.5 lb Page 89 / 109 System Manual PSR2 Series... -
Page 90: Vni-Ipcov8
TECHNICAL SPECIFICATIONS 8.7.13 VNI-IPCOV8 Parts Dimensions Weight: 0.43 kg / 0.95 lb Page 90 / 109 System Manual PSR2 Series... -
Page 91: Vni-Ipcov15
TECHNICAL SPECIFICATIONS 8.7.14 VNI-IPCOV15 Parts Dimensions Weight: 0.9 kg / 2 lb Page 91 / 109 System Manual PSR2 Series... -
Page 92: Vnt-Adpt
TECHNICAL SPECIFICATIONS 8.7.15 VNT-ADPT Parts X2 (M6x20) X2 (M5x25) Dimensions Weight: 0.35 kg / 0.8 lb Page 92 / 109 System Manual PSR2 Series... -
Page 93: Vnt-Ssbrk8
TECHNICAL SPECIFICATIONS 8.7.16 VNT-SSBRK8 Parts VXTCX 5x25 Dimensions 19,5 Weight: 1.8 kg / 4 lb Page 93 / 109 System Manual PSR2 Series... -
Page 94: Vnt-Ssbrk10
TECHNICAL SPECIFICATIONS 8.7.17 VNT-SSBRK10 Parts Dimensions 24,0 Weight: 2.3 kg / 5.1 lb Page 94 / 109 System Manual PSR2 Series... -
Page 95: Vnt-Ssbrk15
TECHNICAL SPECIFICATIONS 8.7.18 VNT-SSBRK15 Parts Dimensions 30,8 Weight: 2.7 kg / 6 lb Page 95 / 109 System Manual PSR2 Series... -
Page 96: Vnt-Tcbrk
TECHNICAL SPECIFICATIONS 8.7.19 VNT-TCBRK Parts Dimensions Weight: 0.78 kg / 1.8 lb Page 96 / 109 System Manual PSR2 Series... -
Page 97: Vnt-Xhbrk
TECHNICAL SPECIFICATIONS 8.7.20 VNT-XHBRK Parts Dimensions Weight: 0.35 kg / 0.8 lb Page 97 / 109 System Manual PSR2 Series... -
Page 98: Vnt-Ttc
TECHNICAL SPECIFICATIONS 8.7.21 VNT-TTC Parts Dimensions Weight: 1.8 kg / 4 lb Page 98 / 109 System Manual PSR2 Series... -
Page 99: Gpt-Bumper
TECHNICAL SPECIFICATIONS 8.7.22 GPT-BUMPER Parts Dimensions Weight: 20 kg / 44 lb Page 99 / 109 System Manual PSR2 Series... -
Page 100: Lst-Xbow18
TECHNICAL SPECIFICATIONS 8.7.23 LST-XBOW18 Parts Dimensions Weight (each): 8 kg / 17.5 lb Page 100 / 109 System Manual PSR2 Series... -
Page 101: Vxt-Bl820
TECHNICAL SPECIFICATIONS 8.7.24 VXT-BL820 Parts Dimensions Weight: 0.04 kg / 0.1 lb Page 101 / 109 System Manual PSR2 Series... -
Page 102: Gpt-Gstk
TECHNICAL SPECIFICATIONS 8.7.26 GPT-GSTK Parts Dimensions Weight: 26.5 kg / 58.4 lb Page 102 / 109 System Manual PSR2 Series... -
Page 103: Lst-Cover18
TECHNICAL SPECIFICATIONS 8.7.27 LST-COVER18 Parts Weight: 2.7 kg / 6 lb Page 103 / 109 System Manual PSR2 Series... -
Page 104: Lst-Wb18
TECHNICAL SPECIFICATIONS 8.7.28 LST-WB18 Parts Dimensions Weight: 8 kg / 17 lb Page 104 / 109 System Manual PSR2 Series... -
Page 105: Ps & Ls Modules & Accessories List
Powered Digital TD Controller 4x1300W NXAMP4x2mk2 Powered Digital TD Controller 4x2500W NXAMP4x4mk2 Powered Digital TD Controller 4x4500W NX.ES104 Ethersound Network Card for NXAMP NX.DT104MK2 Dante Network Card for NXAMP NX.AE104 AES Card for NXAMP Page 105 / 109 System Manual PSR2 Series... - Page 106 LS18 Angle plate (0.2° to 3.15°) GPI-ANPL3 PS15R2 Angle plate (16° to 30°) LSI-CPLA LS18 Mounting plate VNI-IPCOV15 PS8 and PS10R2 IP54 Connector box VNI-IPCOV15 PS15R2 IP54 Connector box VNT-ADPT PS8 flying adaptor Page 106 / 109 System Manual PSR2 Series...
- Page 107 Angle adapter for PS GPT- BUMPER Touring bumper for LS18 LST-XBOW18 Rigging plates for LS18 VXT-BL820 Quick release pin GPT-GSTK Ground stack device for LS18 LST-COVER18 LS18 Cover (single cabinet) LST-WB18 LS18 Whellboard (single cabinet) Page 107 / 109 System Manual PSR2 Series...
-
Page 108: User Notes
USER NOTES 10 USER NOTES Page 108 / 109 System Manual PSR2 Series... - Page 109 Tel: +33 3 44 99 00 70 NEXO S.A. Fax: +33 3 44 99 00 30 E-mail: info@nexo.fr Parc d’activité de la Dame Jeanne nexo-sa.com F-60128 PLAILLY...