Table of Contents
Advertisement
Quick Links
Tubular motor:
GEIGER SOLIDline
Motor control:
SOLIDline SoftPlus-Qi (GU45...-E09)
for cassette awnings and folding arm awnings
Original-Montage- und
DE
Betriebsanleitung
Original assembly and
EN
operating instructions
Notice originale de montage
FR
et d'utilisation
Instrucciones originales de
ES
instalación y funcionamiento
Istruzioni originali di installazione
IT
e funzionamento
www.geiger.de
EN
1
EN
Advertisement
Table of Contents
Related Manuals for GEIGER SOLIDline SoftPlus-Qi GU45-E09 Series
Summary of Contents for GEIGER SOLIDline SoftPlus-Qi GU45-E09 Series
- Page 1 Tubular motor: GEIGER SOLIDline Motor control: SOLIDline SoftPlus-Qi (GU45...-E09) for cassette awnings and folding arm awnings Original-Montage- und Betriebsanleitung Original assembly and operating instructions Notice originale de montage et d’utilisation Instrucciones originales de instalación y funcionamiento Istruzioni originali di installazione e funzionamento www.geiger.de...
-
Page 2: Table Of Contents
1. General information Dear customer, By purchasing a GEIGER motor you have decided on a quality product from GEIGER. Thank you very much for your decision and the confidence placed in us. Before you put this drive into operation please observe the following safety instructions. It serves for the prevention of danger and for the avoidance of personal injury and damage to property. -
Page 3: Intended Use
- E09 Motor control Motor head Torque in Nm Motor diameter GEIGER universal drive 4. Safety instructions ATTENTION: Important safety instructions. For personal safety, it is important to follow these instructions. Please keep these instructions for future reference. f Do not allow children to play with stationary controls. Keep remote controls away from children. -
Page 4: Safety Instructions For Assembly
A plug for the disconnection of the motor from the power supply must be accessible after installation. f Damaged connecting cables must be replaced by GEIGER connecting cables of the same type. f The device must be mounted as described in the installation instructions. Fixations shall not be made with adhesives since they are regarded as unreliable. -
Page 5: Installation Instructions
– Place the motor into the existing engine bearer and lock – Place the motor in a compatible engine bearer with clip system and lock with spring or rotating lever The GEIGER SOLIDline motor is suitable for shaft diameters from 50 mm! www.geiger.de... -
Page 6: Information For The Specialist Electrician
UP and DOWN directions. Connecting cables with plug connectors of the Hirschmann Company are tested and approved with couplings of the Hirschmann Company. Electronic / mechanical limit stop Gerhard Geiger GmbH & Co. KG | 100W1512 V001 0120... -
Page 7: Setting Of The End Positions
Connect the adjusting cable to the connecting cable of the motor. Please always connect cores of identical colours here. The assignment of the direction keys 1 and 2 to the direction of rotation depends on the installation situation of the drive. Then connect the adjusting cable to the 230V mains. www.geiger.de... -
Page 8: Obstacle Detection
The motor jerks when starting (runs, • The programming mode is activated. The stops, runs). minimum travel distance has not been fully respected during programming. 12. Maintenance The drive is maintenance-free. Gerhard Geiger GmbH & Co. KG | 100W1512 V001 0120... -
Page 9: Declaration Of Conformity
Gerhard Geiger GmbH & Co. KG Schleifmühle 6 | D-74321 Bietigheim-Bissingen Phone +49 (0) 7142 9380 | Fax +49 (0) 7142 938 230 | info@geiger.de | www.geiger.de Sitz Bietigheim-Bissingen | Amtsgericht Stuttgart HRA 300591 | USt-IdNr. DE145002146 Komplementär: Geiger Verwaltungs-GmbH | Sitz Bietigheim-Bissingen | Amtsgericht Stuttgart HRB 300481 Geschäftsführer: Roland Kraus | WEEE-Reg.-Nr. -
Page 10: Technical Data
The average sound pressure level data are intended for guidance only. The values were determined by GEIGER at a distance of 1 m, with a hanging motor at idle speed and averaged over 10 seconds. There is no reference to any specific test standard. - Page 11 www.geiger.de...
- Page 12 They will be happy to assist you. Gerhard Geiger GmbH & Co. KG Schleifmühle 6 | D-74321 Bietigheim-Bissingen T +49 (0) 7142 9380 | F +49 (0) 7142 938 230 info@geiger.de | www.geiger.de Gerhard Geiger GmbH & Co. KG | 100W1512 V001 0120...
Need help?
Do you have a question about the SOLIDline SoftPlus-Qi GU45-E09 Series and is the answer not in the manual?
Questions and answers