Table of Contents
Advertisement
Quick Links
Tubular motor:
GEIGER-SOLIDline
Motor control:
GEIGER-SoftPlusWireless (GU45..F02)
for cassette awnings
Original-Montage- und
DE
Betriebsanleitung
Original assembly and
EN
operating instructions
Notice originale de montage
FR
et d'utilisation
Instrucciones originales de
ES
instalación y funcionamiento
Istruzioni originali di installazione
IT
e funzionamento
www.geiger.de
EN
1
EN
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for GEIGER SOLIDline GU4506
Summary of Contents for GEIGER SOLIDline GU4506
- Page 1 Tubular motor: GEIGER-SOLIDline Motor control: GEIGER-SoftPlusWireless (GU45..F02) for cassette awnings Original-Montage- und Betriebsanleitung Original assembly and operating instructions Notice originale de montage et d’utilisation Instrucciones originales de instalación y funcionamiento Istruzioni originali di installazione e funzionamento www.geiger.de...
-
Page 2: Table Of Contents
1. General information Dear customer, By purchasing a GEIGER motor you have decided on a quality product from GEIGER. Thank you very much for your decision and the confidence placed in us. Before you put this drive into operation please observe the following safety instructions. It serves for the prevention of danger and for the avoidance of personal injury and damage to property. -
Page 3: Intended Use
GU 45 Motor control Torque in Nm Motor diameter GEIGER universal drive 4. Safety instructions ATTENTION: Important safety instructions. For personal safety, it is important to follow these instructions. Please keep these instructions for future reference. f Do not allow children to play with stationary controls. Keep remote controls away from children. -
Page 4: Safety Instructions For Assembly
A plug for the disconnection of the motor from the power supply must be accessible after installation. f Damaged connecting cables must be replaced by GEIGER connecting cables of the same type. f The device must be mounted as described in the installation instructions. Fixations shall not be made with adhesives since they are regarded as unreliable. -
Page 5: Installation Instructions
– Place the motor into the existing engine bearer and lock – Place the motor in a compatible engine bearer with clip system and lock with spring or rotating lever The GEIGER SOLIDline motor is suitable for shaft diameters from 50 mm! www.geiger.de... -
Page 6: Information For The Specialist Electrician
30 min. The learning mode is necessary in order to transmit radio codes, or in order to be able to adjust the end positions again. Gerhard Geiger GmbH & Co. KG | 100W0537 V001 0718... -
Page 7: Learning/Deleting The Radio Code
From far range, press the up or down button and hold until you hear the motor (1 x ‘Click- Click’). Please note! The correct button allocation for up and down happens automatcally after programming of the end position is complete. www.geiger.de... - Page 8 Please note! When changing the end position, the power level is reset to its max. standard setting (Level 4). 15 cm Gerhard Geiger GmbH & Co. KG | 100W0537 V001 0718...
-
Page 9: Teaching-In The Incline Position
To deactivate the close-range function, move the desired hanging to the upper end position, push the „UP“ button and keep it pushed for about 5 seconds until the motor confirms (2 x „click-click“). The motor must be disconnected from the mains briefly to active the close-range function. www.geiger.de... -
Page 10: Geiger-Powertronic
• When the end position teach-in mode is activated, the power level is reset to • level 4 (GEIGER-delivery setting). • Only activate the GEIGER-Powertronic after the end positions have been taught-in and a complete trial has been conducted. Gerhard Geiger GmbH & Co. KG | 100W0537... - Page 11 Activating the GEIGER-Powertronic click- 1. At close range, press the ‘Up’ or ‘Down’ button and click hold approx. 3 seconds until you hear the motor (1 x ‘Click-Click‘). 2. From far range, press the ‘Up’ or ‘Down’ button and hold approx. 1 second until you hear the motor (1 x ‘Click-Click‘).
-
Page 12: Function Description Of Radio Motor
In the delivery state, each GEIGER radio receiver and radio transmitter is equipped with the “GEIGER-Code“ + + + + - + - so that the motor can be operated immediately, in order, for example, to facilitate the installation of hangings on the winding shaft. -
Page 13: Initiating End Positions
The running direction in which the obstacle was recognized is blocked. The block is removed if the motor has been operated in the opposite direction for a certain time. An obstacle must thus first be released before the motor can be operated again in the direction of the obstacle. www.geiger.de... -
Page 14: End Position Correction
• Exchange the batteries in the hand-held transmitter. • The close range is deactivated. To activate the close range disconnect the motor from the electrical supply for about 3 seconds. 20. Maintenance The drive is maintenance-free. Gerhard Geiger GmbH & Co. KG | 100W0537 V001 0718... -
Page 15: Declaration Of Conformity
Gerhard Geiger GmbH & Co. KG Schleifmühle 6 | D-74321 Bietigheim-Bissingen Phone +49 (0) 7142 9380 | Fax +49 (0) 7142 938 230 | info@geiger.de | www.geiger.de Sitz Bietigheim-Bissingen | Amtsgericht Stuttgart HRA 300591 | USt-IdNr. DE145002146 Komplementär: Geiger Verwaltungs-GmbH | Sitz Bietigheim-Bissingen | Amtsgericht Stuttgart HRB 300481 Geschäftsführer: Dr. -
Page 16: 22. Technical Data
The average sound pressure level data are intended for guidance only. The values were determined by GEIGER at a distance of 1 m, with a hanging motor at idle speed and averaged over 10 seconds. There is no reference to any specific test standard.
Need help?
Do you have a question about the SOLIDline GU4506 and is the answer not in the manual?
Questions and answers