Summary of Contents for Exerpeutic Folding Upright Bike with Pulse
Page 1
oldin ng U prig ght B Bike w with Puls IMPO ORTANT: Read d all instru uctions ca refully bef fore using g this prod duct. Ret tain this owne er’s manu al for futu ure referen nce. The s specificatio ons of this product m...
SERVICE IMPORTANT: FOR NORTH AMERICA ONLY For damaged or defective products, questions, replacement parts or any other service support, please contact our customer service department (Open 8:00 AM - 5:00 PM Pacific Standard Time, Daily) by the below methods: For Best Service, please Email: Service@paradigmhw.com * Response Time: 1-2 Business Days Website:...
PRODUCT SAFETY Basic precautions should always be followed when using this equipment. Read all instructions before using this equipment which include the following safety instructions: Read all the instructions in this manual and do warm up exercises before using this equipment. Before exercising, and in order to avoid injuring your muscles, it is recommended that you perform warm-up exercises for every muscle group.
PART LIST Description Q’ty Description Q’ty 001 Front Frame 029 Hexagon Nut Cap M8 002 Rear Frame 030 Curve Washer Ø8.2xØ22.2 003 Rear Stabilizer 031 Front Stabilizer Ø50x1.5tx550L 004 Handlebar 032 C-ring Ø10 005 Seat Post 033 Flat Washer Ø8.2xØ16.8 006 Seat Cushion 034 Nylon Nut M8 007 Left Pedal...
Page 9
PART LIST Description Q’ty Description Q’ty 060 Washer Ø8.2x Ø25x2.0t 075 Screw M5x10 061 Flat Phillips Head Screw M6x10 076 Hexagon Socket Bolt M8x43L 062 Holder 077 Handlebar End Cap Ø25.4 Round Phillips Head Screw Front Frame Support Tube End M4x10 Cap Ø22.2 064 Plastic Washer...
Page 11
SSEMBL Tool: 13-15m mm Wrench Front S Stabilizer (3 Trans sport Whee Step 1 Frame set Extend the Front Fram me (1) and d the Rear Frame (2) . Rest the Rear Fram me Support t Tube (67) nto the hoo oked plate on the Fro ont Frame...
ASSEMBLY Tools: 13-15mm Wrench 19mm Wrench Step 2 Remove the Left and Right Nylon Nuts (84) & (86) from the Left and Right Pedal (7) & (8). The Cranks, Pedals, Pedal Shafts, and the Pedal Straps are marked “R” for Right and “L”...
Page 13
ASSEMBLY Tool: 5mm Allen Wrench with Phillips Screwdriver Step 3 The Seat Cushion (6) has 2 sets of adjustment holes. It is recommended that users between 5’1” – 5’6” use the holes towards the rear. It is recommended that users between 5’7” to 6’3” us the holes towards the front. Align the bolt holes on the underside of the Seat Cushion (6) with the holes on top of the Seat Post (5).
Page 14
ASSEMBLY Tool: 5mm Allen Wrench with Phillips Screwdriver Step 4 Place the Handlebar (4) onto the Front Frame (1), and remove the Console Cover (69) from the back of the Handlebar (4). Turn the Tension Control Knob (13) to level 8 and hook the cable end of the Tension Control Knob (13) into the cable lock of the Tension Cable (15) (See Fig AA-3).
STORAGE Upper Pin Hole Lower Pin Hole For your convenience, the bike can be folded up for storage. Remove the Safety Pin (22) from the upper pin hole on the Front Frame (1) Fold the Front and Rear frames together. Re-insert the Safety Pin (22) into the lower pin hole on the Front Frame (1) to secure the Front and Rear frames together.
ADJUSTMENTS Tension Control Knob (13) Adjusting the Tension Control Knob Increase Tension: Turn the tension control knob (13) clockwise. Decrease Tension: Turn the tension control knob (13) counterclockwise. Seat Height Adjustment Knob (14) Adjusting the Seat Height Loosen the Seat Height Adjustment Knob (14) by turning it counterclockwise and pull to release the pin.
Page 18
DJUSTME ENTS usting the e Pedal St trap L ma e Left Peda al Strap (87 7) has an L L marked o on the stra p (see Fig ure 1). ap the slott ted end of the Left Pe edal Strap (87) onto t the tab on...
TRANSPORTING THE BIKE Transporting the Bike Hold the Handlebar (4) and tilt the bike forward until the wheels on the Front Stabilizer (31) make contact with the floor. Push or pull the unit to the desired location, then gently lower the Rear Stabilizer (3) back down to the ground.
MAINTENANCE & TROUBLE SHOOTING MAINTENANCE Cleaning The bike can be cleaned with a soft clean damp cloth. Do not use abrasives or solvents on the plastic parts. Please wipe your perspiration off the bike after each use. Be careful not to get excessive moisture on the computer display panel as this might cause an electrical hazard or the electronics to fail.
Page 21
MAINTENANCE & TROUBLE SHOOTING TROUBLE SHOOTING PROBLEM: The pedals came unscrewed while in use. SOLUTION: Reinstall the pedals and if you cannot, contact Customer Service. PROBLEM: How to reset the data on display. SOLUTION: Hold the Mode Key down for 3-10 Seconds, this will reset the display (Note: The Odometer will not be reset.
WARRANTY MANUFACTURER’S LIMITED WARRANTY Paradigm Health & Wellness warrants to the original purchaser that this product is free from defects in material and workmanship when used for the purpose intended, under the conditions that it has been installed and operated in accordance with Paradigm’s Owner’s Manual.
PARTS REQUEST FORM Paradigm Health & Wellness, Inc. EMAIL THIS FORM WITH YOUR RECIEPT OF PURCHASE TO Service@paradigmhw.com * NAME: _______________________________________________________ ADDRESS: ____________________________________________________ CITY ______________ STATE ______________ ZIP ___________________ TELEPHONE: (Day) ____________________________________________ (Night) ____________________________________________ SERIAL#: _____________________________________________________ MODEL#: _____________________________________________________ PURCHASE DATE: _____________________________________________ PLACE OF PURCHASE: _________________________________________ PART # DESCRIPTION “YOUR ORDER WILL BE PROCESSED WITHIN 3 BUSINESS DAYS”...
Need help?
Do you have a question about the Folding Upright Bike with Pulse and is the answer not in the manual?
Questions and answers