Table of Contents
Advertisement
Basic operations
Selecting the DSK material
Selecting the DSK fill signal and DSK source signal
Press the [DSK] button in the AUX bus selection area to
switch the selection of the DSK fill signal (indicator lights in
amber) and DSK source signal (indicator lights in green).
<Selecting the DSK fill signal>
While the indicator of the [DSK] button is lit in amber, press
one of the AUX bus crosspoint buttons 1 to 12 to select the
DSK fill signal.
The indicator of the selected AUX bus crosspoint button
lights in amber. (It lights in red if the selected signal is
being output from the PGM connector.)
KEY1
KEY2
KEY3
DSK1
DSK2
F/S
F/S
F/S
F/S
F/S
AMBER : FILL / GREEN : SOURCE
AUX BUS DELEGATION
AUX
<Selecting the DSK source signal>
While the indicator of the [DSK] button is lit in green, press
one of the AUX bus crosspoint buttons 1 to 12 to select the
DSK source signal.
The indicator of the selected AUX bus crosspoint button
lights in green. (It lights in red if the selected signal is being
output from the PGM connector.)
Since the luminance key is operated as a self key, the key
fill signals are used as the key source signals. When the
luminance key has been selected as the downstream key
type, the key signals will remain unchanged even when the
key source signals are switched.
KEY1
KEY2
KEY3
DSK1
DSK2
F/S
F/S
F/S
F/S
F/S
AMBER : FILL / GREEN : SOURCE
AUX BUS DELEGATION
AUX
DISP
MV1
AUX1
AUX2
AUX3
AUX4
MV2
CAM
AUX /DISP SOURCE
SHIFT
Lighting in amber
DISP
MV1
AUX1
AUX2
AUX3
AUX4
MV2
CAM
AUX /DISP SOURCE
SHIFT
Lighting in green
Linking the DSK fill signal and DSK source signal
selection
1 Press the
CONF
SYS
menu.
2 Use [F1] to display the Key Signal Coupling1 sub menu.
3 Use [F2] to select the linking method for the DSK fill
signal and DSK source signal by using the Fill/Source
item.
Fill To Source When the DSK fill signal is selected, the DSK
Source To Fill When the DSK source signal is selected, the
PGM
PVW
<Fill To Source>
When the DSK fill signal is selected, the DSK source
signal also switches automatically.
Initially, the DSK source signal and the DSK fill signal
will be the same signal.
For example, when "SDI1" is selected for the DSK fill
signal, the DSK source signal also becomes "SDI1".
After that, when the [DSK] button is pressed and lights
in green, "SDI2" is selected for the DSK source signal.
At this time, combination data indicating that the DSK fill
signal is "SDI1" and the DSK source signal is "SDI2" is
recorded on the unit.
After the DSK fill signal and DSK source signal have
been switched to other signals to perform another
operation, if the DSK fill signal is then selected and set
to "SDI1", the saved combination data causes the DSK
source signal to automatically switch to "SDI2".
If the DSK source signal is changed while the DSK fill
PGM
PVW
signal is set to "SDI1", the combination data is updated
to reflect the change, and is recorded on the unit.
<Source To Fill>
When the DSK source signal is selected, the DSK fill
signal switches automatically.
However, be aware that if the [DSK] button is pressed
when it is not lit, the [DSK] button will first light green,
and the mode will be that for selecting the DSK source
signal.
57
button to light it, and display the Config
source signal changes automatically.
DSK fill signal changes automatically.
Advertisement
Table of Contents
