Quick Start - socomec ATyS d M Instruction Manual

3. 04("* 23 13
3.1. Quick Start ATy2 C , /

QUICK START

EN
ATyS d
Remotely operated
Transfer Switching Equipment
Preliminary operations
Check the following upon delivery and after removal of the
packaging:
■ Packaging and contents are in good condition.
■ The product reference corresponds to the order.
■ Contents should include:
Qty 1 x ATyS M
Qty 1 x Emergency handle extension rod
Qty 1 x Set of terminals
Quick Start instruction sheet
Warning
Risk of electrocution, burns or injury to persons and /
or damage to equipment.
This Quick Start is intended for personnel trained in the
installation and commissioning of this product. For further
details refer to the product instruction manual available on
the SOCOMEC website.
This product must always be installed and commissioned
■
by qualified and approved personnel.
■ Maintenance and servicing operations should be
performed by trained and authorised personnel.
■ Do not handle any control or power cables connected to
the product when voltage may be, or may become present
on the product, directly through the mains or indirectly
through external circuits.
■ Always use an appropriate voltage detection device to
confirm the absence of voltage.
Ensure that no metal objects are allowed to fall in the
■
cabinet (risk of electrical arcing).
Failure to observe good enginering practises as well as to
follow these safety instructions may expose the user and
others to serious injury or death.
Risk of damaging the device
In case the product is dropped or damaged in any way it
■
is recommended to replace the complete product.
Accessories
Bridging bars and 125A or 160A.
■
Voltage sensine and power supply TAP.
■
Terminal shrouds.
■
Additionnal aux contact block.
■
Plastic enclosure.
■
Dual Power Supply (DPS).
■
Power Connection Terminals.
■
ATS Control relay ATyS C30 + D10 or D20.
■
ATS control relay ATyS C20.
■
ATS control relay ATyS C40.
■
www.socomec.com
www.socomec.com/en/atys-d-m
To download, brochures, catalogues and technical manuals.
Printing informations: 1 color Black. White paper 90g/m
Printing size: 420x297. Final size 210x297. This page visible first.
A separate sheet for each language.
542 954 B - 06/14 - EN
10 EN
Installation and Commissioning
}}$ 3
STEP 1
M
Cabinet / Back
Plate Installation
STEP 5B
Open the front cover as
shown to put into manual
mode.
Use the handle situated in
the front panel under the cover to operate the
transfer switch.
Check the changeover switch position on the
indicator before operating.
90º
To simplify operation
use the handle with the
extension provided.
STEP 5C
In order to padlock put the
product in manual mode.
Pull the locking mecha-
nism and insert a padlock
as shown.
As standard padlocking in the 0 position.
Configurable to I-0-II (see step 1).
2 .
STEP 2 STEP 3
Connecting the CONTROL /
POWER section AUX POWER
terminal
connections
STEP 4
Manual operation
Whilst in manual mode, check the wiring and
LIbRN SRZHU XS WKHbSURGXFW
90º STEP 5A
Extension
Close the front cover as shown to put the product
into automatic mode. The product is now ready to
receive order inputs based on the following logic.
(Max 8 Nm)
order I
order 0
Padlocking mode
order II
position I
position 0
position II
Note: Excludes position switching delays.
For contactor logic bridge
contact 313 with 317.
To operate: close the
contact corresponding to
the desired position.
1x 4-8 mm
STEP 5A
Automatic Operation
STEP 4
STEP 5B
CHECK
Emergency Manual
Operation
STEP 5C
Padlocking
Check
Automatic operation
Impulse logic Contactor logic
,PS PV
STEP 3
Ensure that the
Auxiliary cont
Fitting of the 2nd
To fit an AC, the s
NC changeover c
maintened