Page 1
_________ l � -' -------- - - Модульный автоматический реверсивный рубильник с дистанционным управлением Socomec ATyS d M - руководство по эксплуатации. Юниджет. Постоянная ссылка на страницу: https://www.uni-jet.com/catalog/sistemyi-kommutaczii,- kontrolya-i-zashhityi/pereklyuchateli-nagruzki/socomec-atys-d-m.html...
Page 2
ATyS d M Remotely Operated Transfer Switching Equipment www.socomec.com...
Page 3
To download, brochures, catalogues and technical manuals : This manual is available for download in French, English, German, Italian, Spanish, Dutch, Portugese, Russian, Polish, Turkish and Chinese. ATyS d M - 542 929 C - SOCOMEC...
One must also refer to and respect markings on the product prior to installation and commissioning for values and limits speciic to that product. • Using the product outside the intended scope, outside SOCOMEC recommendations or outside the speciied ratings and limits can cause personal injury and/or damage to equipment.
Transformer Management Management atyS d M atyS d S RTSE (DPS) atyS d Small Genset RTSE (DPS) with DPS Side by Side atyS S (RTSE) atyS r ATyS Configuration Small Genset RTSE RTSE The UL version of ATyS r is available from 100 - 400A ATyS d M - 542 929 C - SOCOMEC...
* 3 inputs / 3 outputs (programmable). ** Product reference is different: communication by RS485 connection (MODBUS) allows up to 31 ATyS M to be connected to a PC or a PLC over 1500 m. ATyS d M - 542 929 C - SOCOMEC...
Printing size: 420x297. Final size 210x297. This page visible first. A separate sheet for each language. For contactor logic bridge contact 313 with 317. CORPORATE HQ CONTACT: SOCOMEC SAS, 1-4 RUE DE WESTHOUSE, 67235 BENFELD, FRANCE To operate: close the contact corresponding to the desired position. 1x 4-8 mm Non contractual document.
Page 12
1309 0011 (accessory) C: F1/F2 = fuse 10 A gG Use 35mm screws for 2 modules * Remote orders from ATS controller such as ATyS C20/ Pozidriv PZ2 - 1 Nm C30/C40 or PLC, BMS, etc. ATyS d M - 542 929 C - SOCOMEC...
Note: Excludes position switching delays. A separate sheet for each language. For contactor logic bridge contact 313 with 317. CORPORATE HQ CONTACT: SOCOMEC SAS, 1-4 RUE DE WESTHOUSE, 67235 BENFELD, FRANCE To operate: close the contact corresponding to the desired position. 1x 4-8 mm Non contractual document.
Page 14
1309 0011 (accessory) C: F1/F2 = fuse 10 A gG Use 35mm screws for 2 modules * Remote orders from ATS controller such as ATyS C20/ Pozidriv PZ2 - 1 Nm C30/C40 or PLC, BMS, etc. ATyS d M - 542 929 C - SOCOMEC...
(padlocked). 4.3. Supply types The power supply of ATyS d M is to be 220 to 240VAC ± 20% (176-288Vac) at a frequency of 50/60 Hz and has been developed so as to meet most network conigurations. ATyS d M - 542 929 C - SOCOMEC...
Dedicated to the implementation of a single-phase Ref. : 1309 9056 Single phase ATyS M, it enables easy access to a compact power residential supply switching solution. enclosure 40-160A (HxWxD: 410x305x150mm). IP41 ATyS d M - 542 929 C - SOCOMEC...
Page 17
Supplied from ATS controllers designed for use with products such as measurement circuit: the ATyS d M motorised changeover switch. For further reference 1599 3030 or details refer to the SOCOMEC General Catalogue. DC power supply: reference 1599 3031 ATyS C40 DC power supply: for Gen/Gen applications: reference 1599 3040...
** AC 33iB 160A according to GB 14048.11. This is a class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures. ATyS d M - 542 929 C - SOCOMEC...
0.85 Storage • 1 year maximum • Maximum storage temperature: +55 °C IP rating • IP41 in the SOCOMEC polycarbonate modular enclosure 1 ¡ ¡ • IP2x for non-enclosed modular product Protection class: Class 1 ATyS d M - 542 929 C - SOCOMEC...
Posidriv PZ2 Posidriv PZ2 8.2. Recommanded orientation Recommended 8.3. dimensions of the single phase 8.4. Back plate mounted single product phase product Max : 2 73,5 4 mounting brackets 6x M6 screw - 2,5 Nm ATyS d M - 542 929 C - SOCOMEC...
8.6. Back plate mounted three product phase product MAX : 2 73,5 6 mounting brackets 6x M6 screw - 2,5 Nm 8.7. DIN rail mounted Tighten to avoid movement on the DIN rail. DIN RAIL IEC 60715 Posidriv PZ1 1 Nm ATyS d M - 542 929 C - SOCOMEC...
There are two references available: one for ratings up to 125A, and another rated at 160A. On the ATyS d M the bridging bar (load side) may be it to either side of the product (top or bottom). ATyS d M - 542 929 C - SOCOMEC...
There are two references available: one for ratings up to 125A, and another rated at 160A. On the ATyS d M the bridging bar (load side) may be it to either side of the product (top or bottom). 9.5. Terminal shrouds Ref. 2294 4016 °C °C °K °K ATyS d M - 542 929 C - SOCOMEC...
The enclosure must be wall-mounted using screws (not supplied). Recommended size: M6 50 mm (minimum). Weight : between 8 and 10 kg, depending on the accessories. Only 1 aux contact block may be installed when using this enclosure. 385 mm 225 mm (M6) 193 mm ATyS d M - 542 929 C - SOCOMEC...
10.2.1. Wiring in a polycarbonate enclosure example: neutral on the right Max cable size 25 mm² 10.2.2. Extension unit Ref. 1309 9007 Enables you to allocate additional space to the polycarobonate enclosure (ref. 1309 9006). ATyS d M - 542 929 C - SOCOMEC...
Rating conversion table for use in single phase and two-by-two parallel pole set up. (Max ambient temperature = 40 °C). Nominal current rating in three-phase (A) Nominal current rating in single-phase (2 poles in //) (A) ATyS d M - 542 929 C - SOCOMEC...
The product is delivered in the 0 position and in auto mode. Maximum control cables length = 10 m. In case of longer distance, use control relays. Ensure that the product is in Manual Mode (front cover open). ATyS d M - 542 929 C - SOCOMEC...
Control of position I and II have priority on control of position 0. 12.2. Auxiliary contact operating schedule Position I Position 0 Position II C.A. Position I 11-14 Closed 11-12 Open C.A. Position 0 01-04 Closed 01-02 Open C.A. Position II 21-24 Closed 21-22 Open ATyS d M - 542 929 C - SOCOMEC...
• To lock the changeover switch (padlock). • To manually operate the changeover switch using the handle. As soon as manual mode is activated, remote orders are is inhibited Manual Mode Manual changeover locking switching ATyS d M - 542 929 C - SOCOMEC...
Close the cover to enter automatic mode. Make sure that the changeover switch is in automatic mode (AUT LED lit). 13.5.1. Sealable Auto/Manual cover Auto/Manu mode can be protected by sealing the standard Auto/Manu cover as shown. ATyS d M - 542 929 C - SOCOMEC...
(1st order received is held until no longer maintained). position II • If order I or II disappears, the device returns to maintened zero position. (With the power supply available). (Note : Excludes position switching delays) ATyS d M - 542 929 C - SOCOMEC...
Power Supply. (capable to transfer to the available source with that source available only). for full dPS functionality add a dPS reference 1599 4001 as shown above. ATyS d M - 542 929 C - SOCOMEC...
Good engineering practice is imperative whilst all necessary precautions must be taken to ensure that the intervention (whether directly or indirectly) remains safe in all aspects. ATyS d M - 542 929 C - SOCOMEC...
Check the mechanical position of the changeover switch: - Locking is only possible in position 0 as standard The product cannot Locking is possible - Locking in positions 1-0-2 is possible by modifying the product in be locked accordance with the instructions ATyS d M - 542 929 C - SOCOMEC...
Need help?
Do you have a question about the ATyS d M and is the answer not in the manual?
Questions and answers