Advertisement
NOTICE: Please check contents of package for any damage and make sure all parts fit correctly and you
are happy with the product before removing protective film. Once the film is removed you cannot return
the product for a full refund.
Be sure to read these instructions thoroughly before opening and installing the Bobcat 3400 Polycarbonate
Windshield.
1. Start by pulling everything out of the box and find a clean area to lay it down and install the hardware.
Check over the parts included in the cartons with the parts list shown below:
1 ¾" Loom Clamps-----------------------8 each
1" Stainless Steels Bolts----------------12 each
1 ¼" Stainless Steels Bolts--------------4 each
Stainless Steel Washers-----------------34 each
Stainless Steel Lock Nuts----------------8 each
Plastic Thumb Nuts-----------------------6 each
Stainless Steel Nuts-----------------------4 each
55" Rubber Gasket------------------------1 each
Bent Polycarbonate Braces--------------2 each
Polycarbonate Windshield---------------1 each
2. Next take the rubber gasket and starting at one end firmly place along entire bottom edge of the
Windshield. You will need to peel back the protective film from the edge to install the gasket. If you
leave the bulk of the protective film on while doing the installation, you can keep from scratching the
windshield.
3. Next take the two bent Polycarbonate braces and install them on the windshield. You will notice that
one of the braces is shorter; this is the top brace and will go on the outside of the windshield at the top of
the windshield. The bend will be above the bolts when installed. The bottom brace will go just below
the hinge on the inside of the windshield. As before, the bend will be above the bolts, when installed the
brace should look like a shelf pointing towards the rear of the vehicle.
Instructions for Installation and Care of
Bobcat 3400
Folding Polycarbonate Windshield
BC-3400-WD03
2515 Bypass Rd
Flemingsburg, KY 41041
(606) 845-7439
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Over Armour Offroad BC-3400-WD03
Summary of Contents for Over Armour Offroad BC-3400-WD03
- Page 1 Bobcat 3400 Folding Polycarbonate Windshield BC-3400-WD03 NOTICE: Please check contents of package for any damage and make sure all parts fit correctly and you are happy with the product before removing protective film. Once the film is removed you cannot return the product for a full refund.
- Page 2 4. Now you are ready to place the windshield on the Bobcat and attach to the roll cage. NOTE: THE BEND AT THE TOP OF THE WINDSHIELD SHOULD GO BELOW THE TOP TUBE. The diagram below shows the proper placement for the hardware. Install the clamps as shown for the top two slots in the windshield only.
- Page 3 6. Finally install a clamp around the tube blow the hinge as shown below. You will use the 1 ¼” bolts here. This clamp holds the bottom of the windshield down. 7. Now you are ready to take it out and enjoy. To clean the windshield, always clean using a liquid of some sort to decrease the chance of scratches.
- Page 4 - a 25% restocking fee will apply. If ordered from Over Armour Offroad please call at 606-845-7439 to gain a return authorization number, use our preferred shipping carrier (UPS) to return the item (unless the item is defective, you are responsible for paying the shipping to return the item.) Any returns submitted to Over Armour Offroad without a return...
- Page 5 Warranty To The Owner of this Product: Thank you for purchasing one of Over Armour Offroad Cab Enclosures, Tops &/or Windshields! Below are the terms under which your product is covered under our manufacturer’s warranty. 30 Day Warranty which includes and is not limited to replacing the enclosure, tops and/or windshield due to defect of the product.
Need help?
Do you have a question about the BC-3400-WD03 and is the answer not in the manual?
Questions and answers