Advertisement
INSTALL INSTRUCTIONS C‐VS‐1800‐CHGR‐2
18" Vehicle Specific Console for 2016‐2020 Dodge Charger
Police Pursuit Street Appearance Package (order code AEB)
With 12.1‐inch large touchscreen display option (order code AV2)
TOOLS NEEDED:
Phillips Screw Driver
Wire Crimping tool
QTY
PARTS DESCRIPTION
1
Main Console Housing
1
Floor mount bracket
1
Passenger side trim panel
1
Driver side trim panel
1
HVAC Support bracket
C‐HK‐326
QTY
PARTS DESCRIPTION
1
1" Grommet
2
6mm Flange nut
1
O ring for dual USB plug
1
O ring for AUX panel
3
1/4" x 3/4" Lag bolt
4
#8‐18 x 1/4" screw
2
#10 x 3/4" Sheet metal screw
CM008543
CM008541
Check for obstructions (Wires, brake lines, fuel tank, etc.) before drilling any holes!
Socket set (Standard & Metric)
T‐20 Torx Bit
CM007280
Always
Read all instructions before installing any Havis, Inc. products.
Use hardware provided with install kit
Wire Cutters
PART #
CM008536
CM007280
CM008542
CM008541
CM008543
PART#
GSM20093
GSM30141
GSM31342
GSM31344
GSM33060‐1
GSM33178
GSM33195
CM008542
!
7/16 wrench
CM008536
C-VS-1800-CHGR-2_INST_6-17
Advertisement
Table of Contents
Related Manuals for Havis C-VS-1800-CHGR-2
Summary of Contents for Havis C-VS-1800-CHGR-2
- Page 1 CM008543 C‐HK‐326 QTY PARTS DESCRIPTION PART# 1 1” Grommet GSM20093 2 6mm Flange nut GSM30141 1 O ring for dual USB plug GSM31342 1 O ring for AUX panel GSM31344 3 1/4" x 3/4" Lag bolt GSM33060‐1 4 #8‐18 x 1/4" screw GSM33178 2 #10 x 3/4" Sheet metal screw GSM33195 CM008542 CM008543 CM008536 CM007280 CM008541 Always ! Read all instructions before installing any Havis, Inc. products. Check for obstructions (Wires, brake lines, fuel tank, etc.) before drilling any holes! Use hardware provided with install kit C-VS-1800-CHGR-2_INST_6-17...
- Page 2 View of Street Appearance Package Charger full Remove cover in front of armrest. length console and Large touch screen display. ( OEM order codes AEB & AV2 ) Unsnap side trim surrounding HVAC and radio Locate two (2) screws under HVAC control. controls. Remove screws and set aside for future use. Pull HVAC controller towards rear of vehicle and unplug. C-VS-1800-CHGR-2_INST_6-17...
- Page 3 Slide console towards the rear and remove. Remove rubber cover inside center console. Remove vent assembly by lifting and pulling Remove four (4) OEM fasteners. towards the rear of the vehicle. Remove dual USB assembly out of the back of the Remove AUX module from center console. Remove entire wiring harness from the console. console. Install front mounting plate to OEM studs with Snap HVAC bracket onto the HVAC and radio supplied 6mm flange nuts. Leave loose until later. controller. ...
- Page 4 Confirm everything is lined up and tighten Install the bracket and controller into the hardware. dash using #10 x 3/4" sheet metal screws. Slide C‐VS‐1800‐CHGR‐2 console housing into the Line up to front mounting plate and loosely install with 1/4" x 3/4" carriage bolts and serrated nuts. vehicle towards the dash. Install driver side trim panel using #8‐18 x 1/4" Install the previously removed dual USB assembly Phillips flat head screws. into the passenger side trim panel. Install the trim panel using the #8‐18 x 1/4" flat head screws. C-VS-1800-CHGR-2_INST_6-17...
- Page 5 Attach front panel with eight (8) #8‐18 x 1/4" Place the front panel on the console and plug in flat head screws. the AUX controller Tighten all front hardware at this time. Attach rear of console to floor with 1/4" x 3/4" Confirm function of all the OEM controls including USB and AUX accessories. Lag bolts into the factory clips in floor. Wire and mount control heads as needed. Installation of C‐VS‐1800‐CHGR‐2 console complete. C-VS-1800-CHGR-2_INST_6-17...
Need help?
Do you have a question about the C-VS-1800-CHGR-2 and is the answer not in the manual?
Questions and answers