Page 3
Thank you for choosing the JTS wireless system. In order to obtain the best efficiency from the system, you are recommended to take few minutes to read this instruction manual carefully.
1. Important Caution • Always make all connections before plugging the unit into an AC power outlet. • Do not leave the devices in a place neither with high temperature nor high humidity. • Always do not handle the power cord with wet hands ! •...
4. Parts Identification & Accessories 4-1 Receiver // US-36G2 Power On/Off switch Up button Down button Set button LCD Display Volume control AF signal level RF signal level Antenna DC socket for connection of main unit AF output, jack socket (AF UNBAL)
4-3 Body-pack Transmitter // PT-36BG2 LCD Display Battery Tray Set button: set the configuration of bodypack transmitter Up button: select the settings of transmitter Down button: select the settings of transmitter 4 Pin mini XLR mic. input Power Switch / Mute Antenna Belt Clip LCD Panel of the Body-Pack Transmitter...
5. Preparing Procedures Receiver // US-36G2 (1) Power output connector Plug in one end of AC/DC adaptor cable to DC input socket in the rear panel of receiver, and plug another end into an AC outlet.(Step 1) (2) Audio Output Connector Connect one end of the AF output cable to the AF output socket in the rear panel, then plug another end to the “MIC IN”...
6. Basic Operation 6-1 Receiver // US-36G2 1. Power on: Press 【POWER 】 key once to turn power on. POWER Shut down: press and hold power key for 2 seconds. GROUP MUTE MIN. MAX. VOL. DIVERSITY RECEIVER US-36G2 2. Group adjusting 2-1 Press down SET button for 3 seconds.
Page 20
(1)Press ▲ or ▼ keys to change the frequency at an increment of “+/-” 1MHz . Press SET key to set. (2)The 3 digits on the right of the LCD blinking;press ▲or ▼keys to change the frequency at an increment of “+/-” 0.025MHz,Press SET key to set. GROUP MUTE 4.
Page 21
5. Squelch: Adjust receiving sensitivity 5-1 Press down SET button for 3 seconds. 5-2 Press the SET button several times until the “SQ” is displayed on screen. (1)press ▲or ▼ button keys to adjust receiving sensitivity in the range of -5~+10 ; higher number represents lower sensitivity ;...
Page 22
7. Setting key lock LOCK 7-1 Press down SET button for 3 seconds. 7-2 Press the SET button several times until LOCK the “Lo ON” or “Lo OFF” is displayed on screen. (1)press ▲:Lo ON -- the receiver panel key GROUP functions are locked;...
Page 23
6-2 Handheld Transmitter // Mh-36G2 Power/Mute 1. Power / Mute 1-1. Power On: Press the Power switch to turn on the power. Shut down: Keep pressing down the Power switch and the power is off about 3 seconds later. 1-2. MUTE: After the transmitter’ s power is on, pressing the “Power“...
Page 24
3. Group adjusting 3-1 Press down SET button for 3 seconds. 3-2 the group will flash. (1)Press▲or ▼button to select a desired group (1~6). Press SET key to set. (2)The Channel flash, Press▲or ▼button to select a desired channel. Press SET key to set. Number of channels for each group : Group 1→...
Page 25
5. RF Outputs adjusting 5-1 Press SET button for 3 second, The 3 digits of frequency or channel on the left of the LCD begin to blink. 5-2 Press the “SET” button several times until the “rF Hi “ or “rF Lo” on screen. (1)Press ▲: “rF Hi”, high transmitting power (2)Press ▼: “rF Lo”, low transmitting power (3)Press SET key to save the setting.
Page 26
6-3 Body-pack Transmitter // PT-36BG2 1. Power/MUTE 1-1 Power On: Press the Power switch to turn on the power to the transmitter. Green light: Power on Red light: low battery Shut down: Keep pressing down the Power switch and the power is off about 3 seconds later. Power/MUTE 1-2 MUTE: After the transmitter’...
Page 27
3. Group adjusting 3-1 Press down SET button for 3 seconds. 3-2 the group will flash. (1)Press▲or ▼button to select a desired group (1~6), Press SET key to set. (2)The Channel flash, Press▲or ▼button to select a desired channel, Press SET key to set. Number of channels for each group: Group 1→...
Page 28
5. Microphone Attenuate 5-1 Press down SET button for 3 second, The 3 digits of frequency or channel on the left of the LCD begin to blink. 5-2 Press the SET button several times until the “Att On “ or “Att OFF” on screen. (1)Press▲: Att ON;...
Page 29
(2)Press ▼: “Loc OFF”. (3)Press SET key to save the setting. WIRELESS MICROPHONE SYSTEM...
Page 30
Plug the connector into input socket on the body-pack transmitter. MIC IN (3) Instrument Microphones The system is compatible with JTS various instrument microphones. For detail please refer to user’ s manuals of these microphones.
Page 31
(6) Ear-hook Microphone 1. Lightweight Dual Ear Hook Microphone Try on whether the headset is fit. Adjust the headband to a suitable width. Tighten or loosen the curve of the ear-hook by twisting the loop or expanding it. Curve and bend the boom to fit your face. Attach the detachable cable to a suitable place by a cable clip.
8. Important Notice (1) JTS offers wireless systems in a selection of bands that conform to the different government regulations of specific nations or geographic regions. These regulations help limit radio frequency (RF) interference among different wireless devices and prevent interference with local public communications channels, such as television and emergency broadcasts.