Page 2
Thank you for choosing the JTS wireless system. In order to obtain the best efficiency from the system, you are recommended to take few minutes to read this instruction manual carefully.
Page 3
INDEX 1. Important Caution 2. Features 3. Specification 3-1 Overall System 3-2 Receiver 3-3 Handheld Transmitter 3-4 Body-pack Transmitter 3-5 Optional Condenser Microphone 4. Part Identification & Accessories 4-1 Receiver 4-2 Handheld Transmitter 4-3 Body-pack Transmitter 4-4 Optional Condenser Microphone 4-5 Accessories 5.
1. Important Caution • Always makes all connections before plugging the unit into an AC power outlet. • Do not leave the device in a place neither with high temperature nor high humidity. • Always do not handle the power cord with wet hands! •...
5. Preparing Procedures & Basic Operation 5-1 Receiver (1) Audio Output Connector Connect one end of the AF output cable to the AF output socket in the rear panel, then plug another end to the “MIC IN” input socket of a mixer or amplifier. (Step 1) It is equipped with balanced XLR output and unbalanced Φ6.3mm output, choose the proper way for use.
Page 16
Mute status of RX2 Setting lock-on mod (6) Basic Operation US-902D Pro / US-9216 Series 1. Selecting channel Press the Up or Down button till the RX1 starts flashing, and again press the Up / Down button to select a suitable channel from the pre-set 16 channels. Later the RX1 stop flashing, the receiver will store the channel automatically meanwhile presenting the channel number.
Page 17
2. Setting Lock-On Up and Down buttons till the HOLD starts flashing , the Lock-On Hold both mode is done. To release the Lock-On mode hold both Up and Down bottons for 2 secs. 3. Adjusting Squelch level With the Squelch level control in the rear panel, you can adjust the squelch at a suitable level.
Page 18
5-2 Handheld Transmitter Battery Insertion // Mh-920 / Mh-930 / Mh-850 / Mh-750 (1) Loosen the microphone head counter-clockwise. (Figure 1) (2) Hold on to both battery tray buttons to release it. (Figure 2) (3) Insert 2 pieces of UM-3 1.5 V batteries, remember to match Figure 1 correct polarity.
Page 19
Channel Select // Mh-920 / Mh-930 (1) LCD panel Channel Battery indictor (2) Channel Selection 1. Press the SET button to select between frequency and sensitivity. 2. Press the UP or DOWN button to adjust the channel 3. Press UP or DOWN the “CH”...
Page 20
5-3 Body-pack Transmitter // PT-920B(mi) / PT-850B(mi) (1) PT-920B(mi) LCD panel Main display Battery indictor (2) Basic operation 1. Slide the battery tray cover in the direction of the arrow to open it, insert two 1.5V batteries according the correct polarity, and return the cover.
5-4 Installation of Condenser Microphones (1) Lavaliere microphone Attach lavaliere microphone to a tie, lapel, where is suitable for sound pick-up. Plug the connector into input socket on the body-pack transmitter. PT-920BG (2) Headset microphone Put the headband behind your head, and fix the temples on your ears as shows, then adjust the gooseneck to have best miking.
Page 22
(4) Ear-hook Microphone 1. Lightweight Dual Ear Hook Microphone Try on whether the headset is fit. Adjust the headband to a suitable width. Tighten or loosen the curve of the ear-hook by twisting the loop or expanding it. Curve and bend the boom to fit your face. Attach the detachable cable to a suitable place by a cable clip.
6. System Operation Be sure to mute the audio signal of mixer or amplifier before turning on the receiver or trans- mitter. 6-1 Power on Turn AF level on the receiver completely counter-clockwise to the minimum level, and press the power On/Off switch on the front panel of receiver. As soon as you turn power on of receiver, the power LCD lights on, meanwhile the RF signal and AF level indicate the transmission status, and receiver is ready for operating.
6-3 Using the Body-pack transmitter (1) On the rear panel of PT-920B(Bmi) / PT-850B(Bmi) body-back transmitter, equipped the AF level control. Use the supplied plastic stick to adjust a proper level. (2) The carry case allows the PT-920B(Bmi) / PT-850B(Bmi) to be attached on performer’ s belt, place the antenna towards the back of his body.
Page 25
7. Recommendation (1) In order to achieve the optimum reception condition and also extend the operating distance, please leave a “open space” between the receiver and transmitter. (2) Keep the devices away from the metal objects or any interference sources, at least 50 cm. (3) To avoid the feed-back effect, don’t leave the mic.
8. Important Notice (1) JTS offers wireless systems in a selection of bands that conform to the different government regulations of specific nations or geographic regions. These regulations help limit radio frequency (RF) interference among different wireless devices and prevent interference with local public communications channels, such as television and emergency broadcasts.