Page 1
US-8001D us-8002d(DB) US-8216D Series Instruction Manual...
Page 2
Thank you for choosing the JTS wireless system. In order to obtain the best efficiency from the system, you are recommended to take a few minutes to read this instruction manual carefully.
Page 3
INDEX 1. Important Caution 2. Features 3. Specification 3-1 Receiver// US-8001D(DB)/ US-8002D(DB)/US-8216D 3-2 Handheld Transmitter // Mh-750 / Mh-850 / Mh-8016 3-3 Miniature Head Worn Transmitter/UT-16HW 3-4 Body-pack Transmitter // PT-850B(mi) 3-5 Optional Condenser Microphone 4. Part Identification & Accessories 4-1 Receiver// US-8001D(DB)/ US-8002D(DB)/US-8216D 4-2 Handheld Transmitter // Mh-750 / Mh-850 / Mh-8016 4-3 Miniature Head Worn Transmitter/UT-16HW...
1. Important Caution • Always makes all connections before plugging the unit into an AC power outlet. • Do not leave the device in a place neither with high temperature nor high humidity. • Always do not handle the power cord with wet hands! •...
3-3 Miniature Head Worn Transmitter Model No........UT-16HW Frequency Preparation..PLL Synthesized Control Carrier Frequency Range..502~960 MHz RF Outputs......Maximum 10mW Stability........±10KHz Frequency Deviation.... ±48KHz LED Display......Power On/Off, Low battery Controls......... Power On/Off, AF Level, Channel Selecting, Mute Spurious Emissions.....
4-3 Miniature Head Worn Transmitter/UT-16HW Gooseneck Headband Battery Lid(Color ID):Orang/White/Gray Adjustable elastic headband Input gain Channel selector Power On/Mute/Off switch LED indicator for power On/Off, bettery status and mute Sweat Shield 4-4 Body-pack Transmitter // PT-850B(mi) Mic. input (4 pin mini XLR socket) Power On/Off switch Antenna LED indiccator for power and battery status...
Page 11
Headset Microphone // CM-204 / CM-204U / CM-204UL / CM-225 / CX-504 Gooseneck Headband 4 Pin Mini XLR Windscreen CM-204UL CM-204 CM-204U Standard : 4 Pin Mini XLR 3 Pin Mini XLR 3.5 Stereo Plug CM-225 CX-504...
5. Preparing Procedures & Basic Operation 5-1 Receiver // US-8001D(DB) / US-8002D(DB)/US-8216D (1) Audio Output Connector The receiver equipped with both balanced XLR output and unbalanced φ 6.3mm jack output; you can choose the proper way for using. Connect one end of the Audio cable to the AF output socket in the rear panel of the receiver and plug another end to the “MIC IN”...
5-2 Rack Mounting (1) Before mount receivers onto DR-900 rack adaptor, please release any cables from the rear of the receiver. (2) Turn over receiver and DR-900 rack adaptor simultaneously, there are 4 threaded holes each in the bottom of receiver and rack adaptor for inserting screws. (3) Single receiver Insert in a receiver through the front of DR-900 until it is firmly attached to the rack, then screw on a RP-900 to another side of the rack.
5-3 Battery Insertion of the transmitter (1) Mh-850 & Mh-750 Handheld Transmitter 1. Turn the microphone ball grille counter-clockwise ( Figure 1), press both release knobs to remove the battery tray from the mic. housing ( Figure 2). 2. Insert two 1.5V batteries according to the correct polarity (Step 1 of Figure 3) and return the battery tray back to housing (Step 2 of Figure 3).
Page 18
Plug the connector into input socket on the body-pack transmitter. MIC IN (4) Instrument Microphones The system is compatible with JTS various instrument microphones. For detail please refer to user’ s manuals of these microphones. WIRELESS MICROPHONE SYSTEM...
6. System operation Be sure to mute the audio signal of a mixer or amplifier before turning on the receiver and transmitter. (1)Power on Turn AF level on the receiver completely counter-clockwise to the minimum level, and switch on the receiver. As soon as you turn power of the receiver on, the power LED lights red, meanwhile the RF signal and AF LED light up to indicate the receiver is ready for operating.
Page 20
(3) Using the PT-850B / PT-850Bmi Body-pack transmitter 1. Use the supplied screwdriver to adjust the gain control on the rear panel of PT-850B / PT-850Bmi body-pack transmitter to a proper level. 2. The carry case allows the PT-850B to be attached on performer’ s belt, place the antenna towards the back of his body.
Page 21
(6) Ear-hook Microphone 1. Lightweight Dual Ear Hook Microphone Try on whether the headset is fit. Adjust the headband to a suitable width. Tighten or loosen the curve of the ear-hook by twisting the loop or expanding it. Curve and bend the boom to fit your face. Attach the detachable cable to a suitable place by a cable clip.
Page 22
7. Recommendation (1) In order to achieve the optimum reception condition and also extend the operating distance, please leave a “open space” between the receiver and transmitter. (2) Keep the devices away from the metal objects or any interference sources, at least 50 cm. (3) To avoid the feed-back effect, don’t leave the mic.
8. Important notice (1) JTS offers wireless systems in a selection of bands that conform to the different government regulations of specific nations or geographic regions. These regulations help limit radio frequency (RF) interference among different wireless devices and prevent interference with local public communications channels, such as television and emergency broadcasts.
Page 24
US-8001D /US-8002D /US-8216D Series 59506-036-07...