Table of Contents
Advertisement
www.groupdynamics-laundry.com
sales@groupdynamics.lv
–
Under certain conditions, hydrogen gas may be created in the hot water system that has not been used for two or more
weeks. Hydrogen gas is explosive. If the hot water system has not been used for such period open all hot water taps and let
the water run out for few minutes. This will release any accumulated gas. As this gas is flammable, do not smoke or use
open flames during this time.
–
The instructions and warnings described in this manual do not include all conditions and situations which may occur during
the installation, maintenance or operation of your machine. They must be generally understood. Caution and care are factors
which are not included in the design of this machine and all persons who install, operate or maintain the machine must be
qualified and informed about the operating instructions.
–
If any problems or failures occur which you do not understand, immediately contact your dealer, serviceman or manufacturer.
–
Do not bypass any safety devices or their parts. Any interference to the machine function and design are forbidden and the
manufacturer does not bear any responsibilities in such cases!
–
Before maintenance activities always disconnect the machine power supply!
–
Do not repair or replace any machine parts and do not perform machine service work if it is not recommended in the
maintenance instructions. All other service activities should be provided by qualified service workers.
2.2. SYMBOLS ON THE MACHIME
Warning, read and keep written instructios
Dangerous electric current, electric appliance
Press the emergency button in danger
2.3. IMPORTANT INFORMATION BEFORE INSTALLATION
FOR TRANSPORTATION AND STORAGE
IN CASE OF TRANSPORTATION AND STORAGE, WATCH COMPONENTS PROTRUDING FROM THE
CONTOUR LINE OF MACHINE (DOOR LOCKS ETC.), TO AVOID INJURIES.
– Never push, pull or exert pressure on components protruding from the machine contour line (controls, door locks etc.).
– Make sure that these components are secured so as to avoid damages during machine manipulation and installation.
– In case of the machine transportation by the customer, follow the manufacturer's instructions for transportation,
handling and storage of the product. In case of transportation of machine by the customer the manufacturer
is not responsible for possible damage of machine in the course of transportation. In case of storage the
machine in a free area it must be protected against mechanical damage and weather condition factors.
– The ambient temperature of transportation and storage must be between -25°C to +55°C. Relative humidity
must be between 30% to 90% without condensation.
FOR INSTALLATION
ELECTRICAL CONNECTION, EARTHING AND VENTING OF THE MACHINE, WATER INLETS AND
DRAINAGE MUST BE PERFORMED BY QUALIFIED PERSONNEL WITH A PROPER AUTHORIZATION
ACCORDING TO THE INSTALLATION MANUAL IN COMPLIANCE WITH LOCAL STANDARDS
(APPLICABLE ALSO FOR STEAM CONNECTION ON STEAM HEATED MACHINES).
– Do not install the machine at places exposed to climatic effects or excessive humidity. The machine is not
designed to accept environment with sprayed water.
– Any changes in the machine installations must be approved by manufacturer. Otherwise the manufacturer
is not responsible for possible injuries or damages. Interference and changes in the machine construction
are not allowed and the manufacturer refuses any responsibilities in such cases.
– Define dangerous areas in the laundry room and do not allow people to enter if the machine is in operation.
MACHINE INFORMATION
– This manual contains information for the barrier spring-mounted machine with load of dry linen 90 kg / 198 lb,
140 kg / 308 lb, 180 kg / 396 lb.
– Please, check the type of your machine according to your order and on the machine label which is placed in
electric distributor and find appropriate information in the manual.
– The machine is controlled by an electronic control. Find the programming instructions in the programming
manual. The version with an electronic control is 1 - motor with a frequency controlled drive.
– Heating is provided by electrical heating elements or by steam from your steam system.
– Water inlets can use warm, cold soft, and possibly also cold hard water. A machine can be equipped with
a recycled discharging, extend the quantity of dosing pumps and the soap hopper.
– The machine has 5 hoppers, (10 hoppers, valid for 180 kg / 396 lb) filled from the side part of the washing
machine, fig. 3.2. pos.26.
– The machine workmanship which fulfils The European Agreement requirements is stated in the name plate
by the symbol „CE".
– All machines types are produced according the EMC-directive (Electro-Magnetic-Compatibility). They can
be used in restricted surroundings only (comply minimally with class A requirements). For safety reasons
there must be kept the necessary precaution distances with sensitive electrical or electronic device(s).
513289
PUBLICATION DATE 07/04
Direction of the drum rotation during prewash + wash
Direction of the drum rotation during spin
and moving round a slight amount
INSTALLATION AND MAINTENANCE MANUAL
3
Hide quick links:
Advertisement
Table of Contents
