Warnings; During Transportation And Storage; Machine Symbols - Primus C 6 Installation And Maintenance Manual

2. WARNINGS

TO MINIMIZE THE RISK OF FIRE, INJURY BY ELECTRIC SHOCK OR SERIOUS INJURIES TO
PEOPLE OR PROPERTY DAMAGE, PLEASE READ AND FOLLOW THE FOLLOWING
INSTRUCTIONS.
–
This English version is the original version. Without this version, the instructions are incomplete. Complete instructions
consist of „User´s manual", „Installation and Maintenance manual" and „Programming manual".
–
Before installing, operating or maintaining the machine, read and follow these instructions carefully and keep them in
a handy place for later use. Safety instructions included in manuals for personnel operating the washing machine
must be printed and posted on a visible place near the machine in the laundry room.
–
If any problems or failures occur which you do not understand, immediately contact your dealer, serviceman or manufacturer.
–
Follow all basic and valid safety instructions and laws. Do not bypass the instructions stated in the instruction manual,
and warnings on the labels. The labels must stay on the machine and they must be legible.
–
The machine must be connected to the power, ground, water, ventilation and steam supply according to the installation
manual, in compliance with the local standards done by qualified technicians with proper authorization. The valid
standards for connecting to the local power network (TT / TN / IT, ...) must be followed. In the standard execution,
the washer may not be suitable for connecting to an IT supply system.
–
If you have a machine with frequency inverter do not change the parameters of the inverter. Doing so can cause
serious injury, fire, machine damage, etc.
–
The washer extractor is intended to be permanently connected to fixed wiring.
–
The machine must be connected to the voltage supply throuht the main switch which is a part of electric installation in
the place of the machine installation. This main switch must be easily accessible for the machine operator.
–
Any changes concerning the installation which are not described in this Installation Manual, must be approved by the
supplier or manufacturer. Otherwise, the supplier and manufacturer are not responsible for potential injuries to
operators or for any damages. Interventions into the machine execution or functions are not allowed, and the
manufacturer refuses any responsibility in such cases.
–
Define the dangerous areas in the laundry room and obstruct an admission to them during machine's operating.
–
Operation of the machine with malfunctions, missing parts or open covers is not allowed.
–
Do not tamper with the machine's control.
–
Do not store flammable materials around the machine.
–
Keep the top of the machine clean, with out the presence of flammable materials. Do not wash or spray the machine
with running water.
–
Regularly once a three months check the proper function of ground and emergency button.
–
Disconnect the power supply to the machine before doing any interventions to the machine.
–
When the „O / I" switch is in the position off „O", the electrical parts are still under tension. Pull out the plug from power
supply network. The machine is without tension only when the plug is out of the socket !
–
The emergency stop device is omitted on machines design for coin, token, external payment system or similar
operation for use in self-service situation. The owner-installer-user must provide a remote-located emergency stop
device that is connected to each machine.
–
Do not repair or adjust belt drive when the machine is in operation, plug out the plug for repair or maintenance. Do not
repair or replace any part of the washer, or attempt any servicing unless specifically recommended in the
maintenance instructions. All other servicing should be referred to a qualified service person.
–
The instructions and warnings described in this manual do not include all conditions and situations which may occur
during the installation, maintain or operate of your machine. They must be generally understood. Caution and care are
factors which are not included in the design of this machine and all persons who install, operate or maintain the
machine must be qualified and familiar with the operating instructions.
INSTALLATION AND SERVICE CAN BE DONE ONLY BY A SERVICE ORGANIZATION WITH PROPER
AUTHORIZATION FROM THE MANUFACTURER.

2.1. DURING TRANSPORTATION AND STORAGE

DURING TRANSPORTATION AND STORAGE NEVER PUSH, PULL OR EXERT PRESSURE ON COMPONENTS
PROTRUDING FROM THE CONTOUR LINE OF THE MACHINE (CONTROL ELEMENTS, DOOR LOCKS
ETC.). MAKE SURE THAT THESE PARTS ARE SECURED TO AVOID ANY DAMAGE DURING MANIPULATION
AND INSTALLATION.
If transportation is provided by the customer it is necessary to follow the manufacturer´s instructions concerning transportation,
handling and storage. In this case the manufacturer is not responsible for any damage of machine during transportation.
The ambient temperature for transportation and storage must be between -5°C and +55°C. Relative humidity must be
between 30 % and 90% without condensation. When stored in a free area the machine must be protected against mechanical
damage and weather condition effects.

2.2. MACHINE SYMBOLS

Danger, read and follow written
instructions.
Caution, increased temperature
2 INSTALLATION AND MAINTENANCE MANUAL
Caution, high power voltage,
electrical devices
Caution, outlet of steam
from the machine
PUBLICATION DATE Jan 06 516574