Advertisement
Your Brillion Subsoil Chisel Plow has been designed to give years of trouble-free operation. Proper care and
operation will insure the service and long life built into it.
Study this manual carefully before attempting to assemble or operate the machine. When ordering parts, refer
to the model number and serial number located on the name plate on the mast at the front of the machine. (See
page 4). Please read and record these numbers upon receipt of the machine.
"Right" and "Left", "Front" and "Rear" refer to operator's "Right and Left", "Front" and "Rear" when he faces in the
same direction as the machine will travel.
Federal law requires you to explain the safety and operating instructions furnished with this
machine to all employees before they are allowed to operate the machine. These instructions must
be repeated to the employees at the beginning of each season. Be sure to observe and follow
these instructions for your own and your employee's safety.
A subsoil chisel plow is a fairly simple machine, but it must be operated in a prudent manner.
1.
Never turn corners at a high rate of speed.
2.
Never work under the chisel plow unless it is securely blocked up and cannot be knocked off the blocks,
3.
Always take care in raising and lowering the chisel plow, and be certain that no one is in the way.
4.
Never allow passengers to ride on the chisel plow.
5.
Display the Slow Moving Vehicle emblem when traveling on roads.
6.
When traveling on the road at night, make sure that reflective decals and accessory warning lights
are mounted and visible on the machine. Local regulations should be checked first, and if there
are none, the chisel plow owner should take the initiative to make his machine noticeable at night.
Pictured here are
the safety signs
found on your
subsoil chisel plow.
1. DO NOT LUBRICATE, ADJUST OR REPAIR WHEN MACHINE IS IN MOTION.
2. DO NOT TOW OR TRANSPORT FASTER THAN 15 MILES PER HOUR.
Refer to page 4 for
3. DO NOT RIDE OR ALLOW OTHERS TO RIDE ON THE MACHINE.
4. BLOCK UP ALL HYDRAULICALLY OR MECHANICALLY RAISED COMPONENTS TO
location on machne.
PREVENT UNINTENDED LOWERING OR LOWER THE MACHINE TO THE GROUND TO
MAKE ADJUSTMENT
5. KEEP ALL PERSONS AWAY FROM MACHINE DURING HITCHING AND OPERATING.
6. SLOW DOWN BEFORE MAKING SHARP TURNS OR USING THE BRAKES.
DRIVE SLOWLY OVER ROUGH GROUND, SIDE HILLS, AND AROUND CURVES TO AVOID TIPPING.
7. COMPLY WITH ALL LAWS WHEN TRANSPORTING THE MACHINE ON PUBLIC ROADWAYS.
2
8. INSTRUCT ALL OPERATORS IN THE SAFE OPERATION OF THE MACHINE.
REVIEW THE OPERATOR'S MANUAL FOR CORRECT PROCEDURES.
9. BLOCK IMPLEMENT TO PREVENT MOVEMENT WHEN UNHITCHED FROM TRACTOR.
10. KEEP ALL GUARDS AND SHIELDS IN PLACE WHILE MACHINE OR PARTS ARE IN MOTION.
3
1
. 8J310 - Decal, "Caution" list
2. 2J431 - Decal, Reflective Amber
3. 2J430 - Decal, Reflective Red
4. 9D071- Decal, "Machine Level"
5. 8k829 - Decal, Deep Till Caution
973rev401
INTRODUCTION
LOCATION REFERENCE
SAFETY
This safety alert symbol is used to call your attention to instructions
concerning your personal safety. It is found on your machine and
in this manual. It is important to pay attention the the precautions
indicated and to be alert to the possiblility of personal injury or
death.
CAUTION
OR REPAIRS WHEN NOT IN USE.
Page 3
1
NOTICE
MACHINE SHOULD BE LEVEL
WHEN IN OPERATING POSITION
ADJUST UPPER LINK OF
4
TRACTOR 3-POINT HITCH TO
ACCOMPLISH THIS.
CAUTION
8J310
DEEP TILL OPERATION CAN DAMAGE
UNDERGROUND UTILITIES CAUSING
DANGEROUS CONDITIONS AND
5
DISRUPTING SERVICES. DETERMINE
THE DEPTH AND LOCATION OF BURIED
CABLES, PIPE LINES, AND DRAIN
TILES BEFORE OPERATION.
9D71
8K829
1J534
Advertisement
