Related Manuals for Pilz PSS u2 B1
Summary of Contents for Pilz PSS u2 B1
- Page 1 PSS u2 B1 PSS u2 B4 Control system PSS u2 Remote I/O system PSS u2 Operating Manual-1003626-EN-01...
- Page 2 Preface This document is a translation of the original document. All rights to this documentation are reserved by Pilz GmbH & Co. KG. Copies may be made for internal purposes. Suggestions and comments for improving this documentation will be gratefully received.
-
Page 3: Table Of Contents
Function description Supply groups Section 5 Installation General installation guidelines Dimensions Install backplane Install protective plate Install shield connection element (optional) Section 6 Technical details Section 7 Order reference Product Accessories Operating Manual PSS u2 B1, PSS u2 B4 1003626-EN-01... - Page 4 This operating manual explains the function and operation, describes the installation and provides guidelines on how to connect the product. This documentation is valid for the product PSS u2 B1/B4. It is valid until new documenta- tion is published. 1.1.1 Retaining the documentation This documentation is intended for instruction and should be retained for future reference.
- Page 5 Introduction INFORMATION This gives advice on applications and provides information on special fea- tures. Operating Manual PSS u2 B1, PSS u2 B4 1003626-EN-01...
- Page 6 The backplane can be used to form supply groups Available types: – 1x backplane (backplane with one slot) – 4x backplane (backplane with four slots) Operating Manual PSS u2 B1, PSS u2 B4 1003626-EN-01...
- Page 7 Are familiar with the basic regulations concerning health and safety / accident preven- tion, Have read and understood the information provided in this description under "Safety" Have a good knowledge of the generic and specialist standards applicable to the spe- cific application. Operating Manual PSS u2 B1, PSS u2 B4 1003626-EN-01...
- Page 8 In safety-related applications, please comply with the mission time T in the safety-re- lated characteristic data. When decommissioning, please comply with local regulations regarding the disposal of electronic devices (e.g. Electrical and Electronic Equipment Act). Operating Manual PSS u2 B1, PSS u2 B4 1003626-EN-01...
- Page 9 (right-hand) modules at a supply voltage module. Supply group 1 Supply group 2 Supply group 3 24 VDC + 24 V DC Fig.: Formation of supply groups Operating Manual PSS u2 B1, PSS u2 B4 1003626-EN-01...
-
Page 10: Function Description
2. Use a screwdriver to press the yellow contact block down- wards. The yellow contact block is countersunk. 3. Use a screwdriver to move the yellow contact block into the position shown. Operating Manual PSS u2 B1, PSS u2 B4 1003626-EN-01... - Page 11 Use a screwdriver to press the yellow contact block back into its start position. 3. Move the yellow contact block into the position shown. The electrical connection to the left- hand slot is now established. Operating Manual PSS u2 B1, PSS u2 B4 1003626-EN-01...
-
Page 12: Installation
Damage due to electrostatic discharge! Electrostatic discharge can damage components. Ensure against discharge before touching the product, e.g. by touching an earthed, conductive sur- face or by wearing an earthed armband. Operating Manual PSS u2 B1, PSS u2 B4 1003626-EN-01... -
Page 13: Dimensions
Installation Dimensions 16,9 25,9 Fig.: Dimensions for 1x backplane Operating Manual PSS u2 B1, PSS u2 B4 1003626-EN-01... -
Page 14: Install Backplane
Install backplane CAUTION! Risk of material damage Backplanes may only be inserted or removed when the supply voltage is switched off. Switch off the supply voltage before inserting or removing the backplane. Operating Manual PSS u2 B1, PSS u2 B4 1003626-EN-01... -
Page 15: Install Protective Plate
Electrostatic discharge can damage components. Make sure that the yellow cover plate is fitted at the end of the backplane block. The yellow cover plate is an integral part of the head module. Operating Manual PSS u2 B1, PSS u2 B4 1003626-EN-01... -
Page 16: Install Shield Connection Element (Optional)
Operating Manual PSS u2 B1, PSS u2 B4 1003626-EN-01... -
Page 17: Technical Details
In accordance with the standard EN 60068-2-27 EN 60068-2-27 Airgap creepage In accordance with the standard EN 61131-2 EN 61131-2 Overvoltage category Pollution degree Protection type Mounting area (e.g. control cab- inet) IP54 IP54 IP20 IP20 Housing Operating Manual PSS u2 B1, PSS u2 B4 1003626-EN-01... - Page 18 Dimensions Height 107 mm 107 mm 16,4 mm 53,9 mm Width Depth 32,9 mm 32,9 mm Weight 24 g 74 g Where standards are undated, the 2015-04 latest editions shall apply. Operating Manual PSS u2 B1, PSS u2 B4 1003626-EN-01...
-
Page 19: Order Reference
Features Order No. PSS u2 A SH 4 Shield connection element for module rack 328 820 with 4 slots PSS u2 A LC B4 Inscription holder for module rack 328 916 Operating Manual PSS u2 B1, PSS u2 B4 1003626-EN-01... - Page 20 Front cover Support Technical support is available from Pilz round the clock. Americas Australia Scandinavia Brazil +61 3 95600621 +45 74436332 +55 11 97569-2804 Spain Canada Europe +34 938497433 +1 888-315-PILZ (315-7459) Austria Switzerland +41 62 88979-30 Mexico +43 1 7986263-0...