Table of Contents
Advertisement
5. Setting
This unit requires setting and confirmation of the measuring range, etc. before use. Wrong setting, if any, causes
malfunction of the unit. If setting should be wrong, neither measurement nor output becomes correct.
Carefully read the instruction manual before setting the unit.
■ Default setting
The default settings are as specified below at the delivery time. Set them according to the working conditions.
The input circuit of this product is the common use of 3-phase 3-wire (3φ3W), single-phase 2-wire (1φ2W), and
single-phase 3-wire (1φ3W). In case an input circuit is designated at the case of an order, it is shipped by
the default value of the designated input circuit. And, in case it does not do designation of the input circuit
(with no designation), it is shipped by the default value of 3-phase 3-wire (110V).
The unit will be delivered with your specified setting values, if so specified.
№
Setting item (
Pattern
Main monitor
Sub monitor (Left)
Display
1
pattern
Sub monitor (Center)
Sub monitor (Right)
Bar graph
Factor
Alarm output
2
(
３
)
Reset method
Contact delay time
Instant
Voltage upper limit
3
measurement
Voltage lower limit
detection
Action
4
Backlight
Brightness (
Voltage range
Digit number of voltage
Measurement
range
5
range
Frequency range
Digit number of frequency
range
Output factor 1
Analog output
Output factor 2
6
３
(
)
Output factor 3
Low input cut
7
External operation input (
Voltage
Measurement
8
display ON/OFF
Frequency
Phase wire change(
9
Input circuit
Input voltage (
Output 1
Analog output
10
adjustment
Output 2
３
(
)
Output 3
３
Note(
) A setting item is not displayed in case there is no corresponding option.
４
Note(
) In the case of green backlight, it does not indicate the setting item of brightness.
５
Note(
) If input circuit phase wire change setting is changed, the value (No. 1 to 8) of setting 1 and setting
2 will return to the default setting of the switched phase wire.
６
Note(
) When phase wire change setting of an input circuit is set as 3φ3W (or 1φ2W) and the input voltage
setting is changed, the voltage range returns to the default value of the phase wire.
(For example：In case of 3φ3W, 6600V at the case of 110V setting, 220V at the case of 220V setting.）
５
６
)(
)
110V input 220V input
Pattern 1
V(UV)
V(VW)
Nothing
V(WU)
V(UV)
Voltage (OR of each
line voltage)
AUTO
0 second
OFF
OFF
AUTO
４
)
3（Middle）
6600V
4 digits
45.0～65.0Hz
3 digits
V(UV)
V(VW)
V(WU)
OFF
３
)
Alarm reset
ON
ON
５
)
3φ3W
６
)
110V
Bias adjustment
0.0％
Span adjustment
100.0％
Bias adjustment
0.0％
Span adjustment
100.0％
Bias adjustment
0.0％
Span adjustment
100.0％
3-phase 3-wire
Single-phase 3-wire
Pattern 1
V(UN)
V(WN)
Nothing
V(UW)
V(UN)
Voltage (OR of each
line voltage)
AUTO
0 second
OFF
OFF
AUTO
3（Middle）
220.0V
110.0V
4 digits
45.0～65.0Hz
3 digits
V(UN)
V(WN)
V(UW)
OFF
Alarm reset
ON
ON
1φ3W (U-W-N)
220V
300V
0.0％
100.0％
0.0％
100.0％
0.0％
100.0％
4
Single-phase
(U-W-N)
110V input 220V input
Pattern 1
V
Nothing
Nothing
Nothing
V
Voltage
AUTO
0 second
OFF
OFF
AUTO
3（Middle）
3300V
4 digits
45.0～65.0Hz
3 digits
V
OFF
OFF
OFF
Alarm reset
ON
ON
1φ2W
110V
0.0％
100.0％
0.0％
100.0％
0.0％
100.0％
SVLC-212-175
220.0V
220V
Advertisement
Table of Contents
