Rangemaster Professional 90 Gas FSD User Manual page 33

WARNING - SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
of electrode and fit to new electrode. Fit new electrode
to burner.
Reassemble in reverse order. Check ignition.
20. To Remove Grill Door
Remove L H side panel (see 3). Remove the plinth
(4 screws) and the central vertical cover (5 screws).
Remove the two countersunk screws (1 each side)
securing the grill hinge arms to the front of the grill
chamber.
NOTE: The arms are spring tensioned. Carefully
remove the grill door. Retain the gaskets.
Reassemble in reverse order ensuring that the gasket
is fitted between the hinge arm and the front of the grill
chamber.
21. To Remove Main Oven Door
Open oven door and remove Handyrack (where fitted)
by springing one side out of the bracket on the door and
sliding the other side free. Support the door and remove
the two screws securing the upper hinge and packing to
the cooker front. Remove the door from the lower hinge
by lifting slightly and moving outwards.
Reassemble in reverse order.
22. To Change Main Oven Door Outer Panel
Move the cooker forward to gain access to the sides.
Open the oven door slightly and remove the front panel
fixing screws from the door sides (two each side).
Carefully lift off the outer door panel.
Remove door handle from panel by unscrewing 2
retaining nuts. Fit door handle to new panel
Fit panel to door. Reassemble in reverse order.
23. To Change Main Oven Door Latch
Remove outer door panel (see 15). Remove screws
'B' holding latch assembly to inner door panel. Fit new
catch and reassemble in reverse order.
Check correct door operation.
24. To Change Oven Door Seal
Open oven door. The seal is held in place by small
hooks on the rear face. At the corner pull seal diagonally
away from the door centre until that hook is released.
Proceed to the next hook and release it in a similar way,
and so on. Use force if the hooks are stiff, as the old
seal will be discarded.
When fitting new seal, position the seal join at the
bottom. Hook the new seal in one of the corner holes of
the door, and proceed round the door snapping in each
hook in turn.
25. To Adjust Main Oven Door Catch Keep
Open oven door, slacken off locknut at base of keep,
and screw in or out as required until required fit is
obtained. Retighten locking nut.
26. To Remove Fan Oven Inner Back.
Open RH oven door and remove 4 screws and
washers securing the inner back to the back of the
oven. Carefully lift away the inner back. Reassemble
in reverse order making sure that the 4 screws and
washers are fully tightened.
27. To Remove Tall Oven Door
Open oven door, support the door and remove the two
screws securing the upper hinge and packing to the
cooker front. Remove the door from the lower hinge by
lifting slightly and moving outwards.
Reassemble in reverse order.
28. To Change Tall Oven Door Outer Panel
Remove oven door see 16. Lay door face down on a
suitable surface and remove 2 screws from bottom edge
of door and 2 screws from inside face of door.
Remove outer door panel. Remove door handle by
unscrewing 2 screws. Remove 2 cross-headed screws
holding door handle fixing bracket to door panel. Fit
door handle bracket and door handle to new panel.
Fit panel to door. Reassemble in reverse order.
29. To Change Tall Oven Door Magnetic Latch
Remove the control panel (see 4).
Remove the plinth (3 screws) and the central vertical
cover (5 screws). Prize the retaining clip off the magnet
unit. Fit new unit and retaining clip.
Reassemble in reverse order.
Check correct door operation.
30. To Change Ignition Generator
Disconnect from electricity supply.
33