Advertisement
C‐DMM‐3004 Flip up Dash
TOOLS REQUIRED:
Ratchet Wrench
Socket Set
HARDWARE and PARTS:
QTY DESCRIPTION
2
Upper support bracket
2
Side support bracket
4
10‐32 x 1/2" Machine screw
4
#10 Flat washer
2
10‐32 Keps nut
1
VESA rotator plate
1
PVC washer
2
1/4" Plastic washer
2
1/4" Steel washer
2
1/4" Nylock nut
The C‐DMM‐3000 swivel plate accepts C‐MM‐301 offset bracket used with C‐MM‐2XX adaptors.
C‐MM‐2XX series adaptor brackets are not needed for most VESA 75 and other Havis Docking Station
CM009068 VESA rotator plate gives additional positioning options, but is not required depending on
Check for obstructions (Wires, brake lines, fuel tank, etc.) before drilling any holes!
INSTALLATION INSTRUCTIONS
2014‐2020 Dodge Durango
Dash panel removal tool
Phillips screwdriver
mounting applications.
mounting preference.
Read all instructions before installing any Havis, Inc. products.
Use hardware provided with install kit
Monitor Mount
Open End Wrench ‐ 7/16"
PART#
CM009333
CM009334
GSM33118
GSM31003
GSM30028
CM009068
CM008582
CM86600
GSM31005
GSM30016
Notes:
Always
!
C‐DMM‐3004_INST_7‐18
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Havis C-DMM-3004
Summary of Contents for Havis C-DMM-3004
- Page 1 CM008582 2 1/4" Plastic washer CM86600 2 1/4" Steel washer GSM31005 2 1/4" Nylock nut GSM30016 Notes: The C‐DMM‐3000 swivel plate accepts C‐MM‐301 offset bracket used with C‐MM‐2XX adaptors. C‐MM‐2XX series adaptor brackets are not needed for most VESA 75 and other Havis Docking Station mounting applications. CM009068 VESA rotator plate gives additional positioning options, but is not required depending on mounting preference. Always ! Read all instructions before installing any Havis, Inc. products. Check for obstructions (Wires, brake lines, fuel tank, etc.) before drilling any holes! Use hardware provided with install kit C‐DMM‐3004_INST_7‐18 ...
- Page 2 C‐DMM‐3004 CM009333 Assembly Upper support bracket GSM33118 10‐32 x 1/2” Machine screw CM86600 GSM31003 1/4" Plastic washer #10 Flat washer GSM31005 1/4" Steel washer GSM30016 1/4" Nylock nut CM009334 Side support bracket CM009068 VESA rotator plate GSM33118 10‐32 x 1/2" Machine screw GSM31003 CM008582 GSM30028 #10 Flat washer PVC washer 10‐32 Keps nut C‐DMM‐3004_INST_7‐18 ...
- Page 3 View of dash center instrument panel Carefully remove trim bezel / panel assembly using plastic panel tool. Remove (4) 7mm head fasteners around OEM Remove trim panel and set aside. screen. Attach the upper support brackets behind the OEM screen mounts and reinstall fasteners. Repeat process for lower side support brackets. Carefully reinstall trim bezel / panel assembly with four Brackets go behind the OEM screen mounts. brackets protruding out of gap between bezel and dash. C‐DMM‐3004_INST_7‐18 ...
- Page 4 Attach the DMM frame to the brackets using 10‐32 Attach VESA rotator plate to the mounting x 1/2" screws and washers at the top and 10‐32 x bracket of the device you are attaching. 1/2" screws, washers, and keps nuts on the side. Attach the rotator plate to the swivel using large PVC Attach the dock to the mounting bracket (with hardware washer, 1/4 nylon washers, metal washers and stop nuts. supplied with dock) and run wires as desired. Installation is now complete. Double check all hardware, latching and wire harness clearance. C‐DMM‐3004_INST_7‐18 ...
Need help?
Do you have a question about the C-DMM-3004 and is the answer not in the manual?
Questions and answers