Download Print this page

G. Paniz FTG Series Instruction Manual page 19

Gas turbo oven

Advertisement

Available languages

Available languages

GAS TURBO OVEN
FTG 300-240-150-120
FUNCTIONING:
Automatic Igniting: When equipment is turned on, it ignites automatically, with three
attempts to light up the flame. Should flame not be detected at the end of the igniting cycle,
display will show "FLAME OUT" . To try lighting up the flame again, press switch key
for 3 seconds.
Steam: It can be activated by pressing switch key
programmed with 10-second intervals between activations.
Lamp: Can be activated by pressing switch key
turn off after 8 seconds.
Flame: The presence of flame will be indicated by a LED flashing on one side of the display
on the top. If, during cooking, flame goes off, the equipment will stop working and display
message "FLAME OUT", and a sound signa l will go off. To light up the flame again, press
switch key
for 3 seconds; then ignition process will start again.
4
Door Opening: Should the door remain open for more than 3 minutes, a message saying
"DOOR" will be displayed and a sound signal will go off. As soon as the door is closed,
automatic ignition of the flame will take place.
End of Cooking: As soon as cooking process is over, the equipment will sound an alarm
and time displays will start flashing. To turn it off, press switch key
turn off by itself. To turn the equipment off after cooking time is over it is necessary to press
On /Off switch key.
SEQUENCE TO TURN OVEN ON:
1- First check whether ga s valves on the cylinder are open, and if the oven is plugged
into the electrical wall socket.
2- Set gas valve to "On".
3- Turn emergency switch key and press "On/Off" .
4- At this moment, controller will proceed automatic ignition of the burner, and display
will exhibit the configurations set at the factory.
To set a new configuration, proceed as follows:
Time and Temperature: To program the temperature, press switch key
3 seconds; indicator display should start flashing indicating that the temperature can be
programmed by pressing switch keys
3
press switch key
again, and time indicator will start flashing. That indicates time can be set
4
by pressing switch keys
3
and
5
. After that, press switch key
will be back to regular control condition.
NOTE: During programming, if there is a pause longer than 3 seconds, equipment will resume
regular control condition.
Steam Time: To adjust steam time, turn oven on pressingkey
show VAP while display on the bottom will show the amount to be programmed. Adjust amount
with keys
and
. Programmed value will be saved after 3 seconds without pressing the keys.
3
5
Turbine: Turbine will activate itself 3 seconds after Emergency Switch key and ON / OFF
Switch key have been pressed.
* Following sequence described above, burner flame wil l light up and go out automatically ,
always keeping temperature that was programmed.
24
. Steam will be activated for time
6
1
; once it has been activated light will only
2
. Note: Oven doesn't
for approximately
4
and
. After you have set the temperature program,
5
4
again, and the equipment
, and display on the top will
6
TRANSPORT
The oven is equipped with four handles on the top so it can be loaded and unloaded.
Whenever loading or unloading always use hydraulic beams or hoists to prevent accidents
and damages to the equipment.
4
RECEIVING
We recommend extra care in inspecting the equipment in order to identify any damages
that may have been caused during its transportation, such as:
Any damages that might have been caused during transportation should be communicated
to the transporting company and to the manufacturer.
UNPACKING
With the help of a crowbar, remove battens that involve the packaging.
After removing equipment from the package, perform visual inspection in order to check
for any possible damages caused during transportation.
TECHNICAL FEATURES / DIMENSIONS
Model
Monophase Source
FTG 120
110 = 4A / 220 = 2A
FTG 150
110 = 4A / 220 = 2A
FTG 240
110 = 9A / 220 = 5A
FTG 300
110 = 9A / 220 = 5A
Model
Working
Pressure
5 Kpa
FTG 120
5 Kpa
FTG 150
5 Kpa
FTG 240
5 Kpa
FTG 300
Model
Amount of 50-g
Rolls of Bread.
120
FTG 120
150
FTG 150
240
FTG 240
300
FTG 300
GAS TURBO OVEN
FTG 300-240-150-120
- Broken or dented parts.
- Parts missing.
Net Weight
(Kg)
170
170
265
280
PG/ h
NG /h
KW / h
Consumption
Consumption
Consumption
3
1,0 Kg
1,27 m
3
1,0 Kg
1,27 m
3
1,2 Kg
1,52 m
3
1,5 Kg
1,90 m
Dimensions of the
Amount o
Production of
Baking Pans
Baking Pans
50-g rolls / h
58 x 70
4
300 x 360
58 x 70
5
375 x 450
58 x 70
8
600 x 720
58 x 70
10
750 x 900
17
Gross Weight
(Kg)
210
210
355
380
Heating
Time
0,5
10 min
0,5
10 min
1,0
12 min
1,0
15 min
Cooking Time
( min )
15 to 18
15 to 18
15 to 18
15 to 18

Advertisement

loading

Related Products for G. Paniz FTG Series

This manual is also suitable for:

Ftg 120Ftg 150Ftg 240Ftg 300