ADJ NINJA 5RX User Instructions page 11

Ninja 5RX
Master-Slave Configuration
to 16 units together and operate without a controller. In a Master-Slave
set up, one unit will act as the controlling unit and the others will react
to the controlling units programs. Any unit can act as a Master or as a
Slave.
1. Using approved DMX data cables, daisy chain your units togeth-
er via the XLR connector on the rear of the units. Remember the
Male XLR connector is the input and the Female XLR connector
is the output. The first unit in the chain (master) will use the female
XLR connector only - The last unit in the chain will use the male
XLR connector only. For longer cable runs we suggest a termina-
tor at the last fixture.
2. On the Master unit press the MENU button until "Slave Mode" is
displayed, and press ENTER. Use the UP and DOWN buttons to
scroll to the "Master" setting and press ENTER.
3. After setting the Master unit to the master setting find and set
your desired operating mode.
4. On the slave units press the MENU button until "Slave Mode" is
displayed, and press ENTER. Choose either "Slave 1" or
"Slave 2" and press ENTER. See page 9 for more info.
5. The slave units will now follow the Master unit.
Ninja 5RX
With this feature you can connect the fixtures to one another
using the IEC input and output sockets. The quantity that can be
connected is 2 fixtures maximum for 120V and 5 fixtures maxi-
mum for 230V. After the maximum amout of fixtures is connected
you will need to use a new power outlet. They must be the same
fixtures. DO NOT mix fixtures.
ADJ Products - www.adj.com - Ninja 5RX Instruction Manual Page 20
Master-Slave Configuration
This function will allow you to link up
Power Cord Daisy Chain
Ninja 5RX
The UC IR (sold separately) infrared remote gives you control of
various functions (See below). To control the fixture you must aim the
remote at the front of the fixture and be no more than 30 feet away.
The Ninja 5RX comes with the Airstream IR remote transmitter.
The transmitter plugs into the headphone jack of your iOS phone
or tablet. To control your IR fixture you must raise the volume to the
maximum on your iOS phone or table and aim the transmitter at the
front of the fixture and be no more than 15 feet away. After you have
purchased the Airstream IR transmitters, the app is a free download
from the app store for your iOS phone or tablet. The app comes with
3 pages of control depending on the IR fixture you are using. Please
see below for IR functions including the corresponding app page.
Works with App page 1.
STAND BY - Pressing this button will blackout the fixture. Press the
button again to return to the initial state.
FULL ON - Hold this button down to fully light up the unit. When you
let the button go, the unit will return to its previous state.
FADE/GOBO - Press this button and use button's 1-9 to select
gobo's 1-9. Press this button twice to select gobo 10. Press and hold
this button and use button's 1-7 to select gobo's 11-17.
"DIMMER +" and "DIMMER -" - Use these buttons to adjust the out-
put intensity.
STROBE - Press and hold this button for strobing.
COLOR - Press this button and use button's 1-9 to select color's 1-9.
Press this button twice to select color 10. Press and hold this button
and use button's 1-4 to select color's 11-14.
1-9 - Use buttons to select your desired color, gobo, or show.
SOUND ON & OFF - Use the buttons to activate and deactivate
sound active mode.
SHOW 0 - Press this button and use button's 1-9 to select show's
1-9. Press this button twice to select show 10. Press and hold this
button and use button's 1-2 to select color's 11-12.
ADJ Products - www.adj.com - Ninja 5RX Instruction Manual Page 21
UC IR Control