Related Manuals for fantastic furniture MONACO Series
Summary of Contents for fantastic furniture MONACO Series
- Page 1 Version 1.0 MONACO TWO PEOPLE Bedside 2 Drawer www.fantasticfurniture.com.au REQUIRED...
- Page 2 Enjoy Your purchase from Australia's Best Value Furniture Store www.fantasticfurniture.com.au PAGE 2...
-
Page 3: Assembly Checklist
Assembly checklist Read through the instructions carefully Make sure you have all the required tools. Never use power tools unless instructed. before you begin. Identify and lay out all of the components Unless instructed, do not fully tighten screws before you begin assembly. until the item is fully assembled. -
Page 4: What You Need
What you need to assemble the product Top Panel (P1) Other tools you need Flat head screwdriver; Phillips head screwdriver; Mallet Drawer Back Panel (P8) (P5) Drawer Left Side (P6) Part list Box 1: Top Panel (P1); Bottom Panel (P2); Left Side Panel (P3); Right Side Panel (P4);... - Page 5 Step 1 You will need 4 x Big Cam Phillips head Bolt (H1) screwdriver Screw 4 x Big Cam Bolts (H1) into Top Panel (P1) as shown. Step 2 Separate the Slide Runners (H15-2) and Slide Tracks (H15-1) from Slide (H15) by following the steps below: Extend the Slide Runner all the way forward.
- Page 6 Step 3 You will need (P4) 2 x Big Cam 2 x Big Wood Dowel (H4) Bolt (H1) 2 x Slide 6 x Screw Track (H15-1) (H7) (P4) Phillips head Mallet screwdriver Insert 2 x Big Wood Dowels (H4) into Right Side Panel (P4). Screw 2 x Big Cam Bolts (H1) into Right Side Panel (P4).
- Page 7 Step 5 This is how a cam nut works..You will need The head of the cam (P4) bolt goes into the open mouth of the cam nut. You then turn the cam nut so it tightens over the bolt. 4 x Big Cam Flat head Nut (H2)
- Page 8 Step 7 (P10) (P4) (P2) (P3) Slide Back Panel (P10) into the grooves as shown. Step 8 You will need This is how a cam nut works..The head of the cam (P1) bolt goes into the open mouth of the cam nut. You then turn the cam nut so it tightens over 4 x Big Cam...
- Page 9 Step 9 You will need 4 x Back Panel 4 x Screw Connector (H13) (H14) XX = YY Phillips head screwdriver If necessary, gently adjust the Top Panel (P1) sideway in either direction until XX and YY are equal. Fix the Back Panel Connectors (H14) with Screws (H13) as shown. Step 10 Insert 1x Small Wood Dowel (H5) into each Drawer left Side (P6)
- Page 10 Step 11 You will need 8 x Screw Phillips head (H6) screwdriver (P8) (P7) (P6) Attach 1x Drawer Side Panel (P6) and 1x Drawer Side Panel (P7) to 1x Drawer Back Panel (P8) with 4 x Screws (H6), so that their grooves are at the same side.
- Page 11 Step 13 You will need (P5) 4 x Small Phillips head Cam Nut (H9) screwdriver (P7) (P9) (P6) Position Drawer Front (P5) onto Drawer Sides (P6) & (P7). Rotate 1x Small Cam Nut (H9) so the arrow points towards the incoming cam bolt and insert the Small Cam Nut (H9) into Drawer Side Panel (P6) or (P7).
- Page 12 Step 15 √ (P1) (P3) (P5) (P5) Move Inner Ball Bearing Track outward. Push Middle Track in. Gently Insert Slide Runner into Ball Bearing Track. (P5) Position Drawer so that Slide Runner (H15-2) aaligns with Slide Track (H15-1) as shown. Gently push drawer into the closed position.
-
Page 13: Job Complete
Step 16 (P11) If the Bedside is not level, you can adjust the height of each Leg by turning the feet of Legs clockwise or counter-clockwise. Step 17 Job Complete ! In the interest of our environment Please dispose of all packaging thoughtfully. www.fantasticfurniture.com.au PAGE 13... - Page 14 THIS TOP IS FINISHED WITH A CLEAR PU LACQUER Avoid placing hot items directly onto the surface unless using a thick insulation material such as placemats or coasters. Heat may lead to discolouration or other damage to the surface of the product. Use a soft cloth that has been dampened in water to clean the surface of this product.