Gabarron Elnur INGENIUM Series Installation Instructions & User Manual page 9

ON/OFF. With the parameter in ON, the open window detection is activated.
ON/OFF. With the parameter in ON, the open window detection is activated.
C6. Adaptive Start Control
-
C6. Adaptive Start Control
ON/OFF. With the parameter in ON, the adaptive start control is activated.
ON/OFF. With the parameter in ON, the adaptive start control is activated.
4. Remote Operation using the Wifi G-Control Hub
EMOTE OPERATION USING THE WIFI G-CONTROL HUB
4.- REMOTE OPERATION USING THE WIFI G-CONTROL HUB
It is possible to control the full operation of the unit remotely with Elnur Gabarron App or Web-App. The unit must be
sible to control the full operation of the unit remotely with Gabarron-Elnur app or app-web. The unit must be
connected to a Wifi G-Control Hub connected to the internet to use this feature.
It is possible to control the full operation of the unit remotely with Gabarron-Elnur app or app-web. The unit must be
ed to a Wifi G-Control Hub connected to the internet to use this feature.
connected to a Wifi G-Control Hub connected to the internet to use this feature.
4.1 To associate the unit to the G-Control Hub, the
ssociate the unit to the G-Control Hub, the discovery mode of the hub must be activated. Press
4.1 To associate the unit to the G-Control Hub, the
the associate button at the back of the Gateway
y mode of the hub must be activated. Press the
for 3 seconds. An orange blinking light every second
discovery mode of the hub must be activated. Press the
e button at the back of the Gateway for 3 seconds. An
indicates association mode.
associate button at the back of the Gateway for 3 seconds. An
blinking light every second indicates association mode.
orange blinking light every second indicates association mode.
now control and adjust the programming and temperatures on the heater via the Gabarron-Elnur app.
You can now control and adjust the programming and temperatures on the heater via the Gabarron-Elnur app.
You can now control and adjust the programming and temperatures on the heater via the Elnur Gabarron app.
disassociate the unit, a reset of the unit must be realized. See "5. UNIT RESET". When the heater is reset, it will
4.3 To disassociate the unit, a reset of the unit must be completed. See "5. UNIT RESET". When the heater is reset,
4.3 To disassociate the unit, a reset of the unit must be realized. See "5. UNIT RESET". When the heater is reset, it will
the programming and revert back to the default settings and also disassociate from the RF network and G-Control Hub.
it will remove the programming and revert back to the default settings and also disassociate from the RF network
remove the programming and revert back to the default settings and also disassociate from the RF network and G-Control Hub.
and G-Control Hub.
NIT RESET
0:00
5. Unit Reset
5.- UNIT RESET
ter reset removes the programming and disassociates the device from the RF network if the unit was associated with a
The heater reset removes the programming and disassociates the device from the RF network if the unit was
The heater reset removes the programming and disassociates the device from the RF network if the unit was associated with a
rol Hub. Default values are established. To reset the unit, hold the OK/Mode and Config/Prog buttons simultaneously
associated with a G-Control Hub. Default values are established. To reset the unit, hold the OK/Mode and
G-Control Hub. Default values are established. To reset the unit, hold the OK/Mode and Config/Prog buttons simultaneously
Config/Prog buttons simultaneously for 10 seconds, the display will show the following to indicate the heater
econds, the display will show the following to indicate the heater has been reset.
for 10 seconds, the display will show the following to indicate the heater has been reset. has been reset.
21.0C
rES
AUTO
rm the reset of the unit, press OK/Mode button, to cancel it any other button can be pressed.
To confirm the reset of the unit, press OK/Mode button, to cancel it any other button can be pressed.
Elnur powered by Gabarrón | INGENIUM WIFI Thermal Radiators | Installation Guide
4.2 With the hub in discovery mode, press the Ok/Mode
4.2 With the hub in discovery mode, press the Ok/Mode
button on the heater for 3 seconds until the Link symbol is
button on the heater for 3 seconds until the Link symbol is
shown.
shown.
To confirm the reset of the unit, press OK/Mode button,
Pro
to cancel it any other button can be pressed.
AUTO
7
7
4.2 With the hub in discovery mode, press the Ok/Mode
button on the heater for 3 seconds until the Link symbol
is shown.
9