Gabarron ECOHHR20 Advanced Installation Instructions
Ecombi hhr smart storage heater
Hide thumbs
Also See for ECOHHR20:
- Installation and user manual (8 pages) ,
- Installation instructions manual (14 pages) ,
- Installation instructions manual (18 pages)
Related Manuals for Gabarron ECOHHR20
Summary of Contents for Gabarron ECOHHR20
- Page 1 ADVANCED INSTALLATION INSTRUCTIONS ECOMBI HHR SMART STORAGE HEATER ECOHHR20 ECOHHR30 ECOHHR40 Please, read these instructions CAREFULLY before installing or using this appliance for the first time.
- Page 2 1. –IMPORTANT INFORMATION When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: • WARNING: Please read all instructions before installing or using this heater for the first time. •...
-
Page 3: Installation Instructions
2. - INSTALLATION INSTRUCTIONS The symbols used in the text are explained below: WARNING This indication shows the possibility of causing death from electric shock. WARNING This indication shows the possibility of causing death or serious injury. CAUTION This indication shows the possibility of causing injury or damage to properties only. Symbol for useful information. - Page 4 3.- Screw on the wall the superior fixing fitting, making the two required drills at the recommended distance depending on the model. Use the dowels and screws contained in the plastic bag to fix the fitting to the wall. 4.
- Page 5 6. - Connect the heater using the wiring diagram included at the end of this manual. Tighten properly the connection block screws. Use only silicone insulated cables. Do not leave any remaining wire inside the heater. WARNING Touching live connections can cause serious personal injury. 7.
- Page 6 9. - Place the heating elements back into their original position. Place the second row of storage bricks with the flat side facing out and always on the heating elements supporting tabs. Next replace the metallic plate in the top of the storage core, between the bricks and the Microthermal insulation panel with the flat side facing up.
- Page 7 RELOCATION WARNING: Relocation to another location must be carried out by an experienced technician. If during reinstallation the thermal insulation shows any sign of damage, it must be removed and replaced by an identical part. MANUALLY RESET TEMPERATURE LIMITER This heater employs a manually reset temperature limiter (see CUT OUT in the connection diagram). This safety device operates when high temperatures are reached at the top of the heater.
-
Page 8: Connection / Disconnection
3. - OPERATING INSTRUCTIONS CAUTION: DO NOT USE THIS HEATER TO DRY CLOTHES. Do not cover this heater at any time. 3.1. CONNECTION / DISCONNECTION Power switch.All models are equipped with a switch on the back side panel. It is used to connect and disconnect HHR. 3.2. -
Page 9: Operation Mode
3.5. OPERATION MODE: The HHR operates in weekly programming mode. The temperature level (ECO, Frost protection and Comfort) can be set for each period of time (30’ minutes) in the different days in the week. Storage heater resistances will operate during off peak rate in order to charge the heater according to the demand of the room. A fan is used to discharge the heating core if necessary to reach the current set point temperature. - Page 10 Set point temperature level forced function It is possible to change temporarily the temperature level for the current time interval. The modification in the temperature level will be maintained until the next changed in programming temperature level. To change temporarily the current temperature level: Hold key for 4 seconds to activate temporarily the Economic temperature in the current temperature level.
-
Page 11: Open Window Detection
Open Window Detection With open window detection activated, the fan assisted discharge and the balance resistance working will be disconnected automatically when a sharp decrease in temperature in the room is detected avoiding energy wastage. After this period of time, the storage heater returns to the prior operation mode. -
Page 12: Default Settings
3.9.DEFAULT SETTINGS: By pushing the clock key at the same time as we turn on the heater with the power switch, located at the right-side panel, software resets to the default settings. Four horizontal blinking segments will appear in the screen to confirm it. The default programming, all time intervals in frost protection temperature level are set. -
Page 13: Cleaning Maintenance Instructions
Ref. 15190720 Ref. 20191056 140ºC Storage Limiter Ref. 15190720 900 Ω Fan Resistor (EcoHHR40) Ref. 15192164 160ºC Cut Out Manually Limiter Ref. 15190730 1050 Ω Fan Resistor (EcoHHR30) Ref. 15192162 Switch Ref. 46100530 1200 Ω Fan Resistor (EcoHHR20) Ref. 15192160... -
Page 14: Connection Diagrams
7.- CONNECTION DIAGRAMS ECOHHR20 ECOHHR30 ... -
Page 15: Technical Features
8.- TECHNICAL FEATURES Model ECOHHR20 ECOHHR30 ECOHHR40 CONNECTION 240V ~ 240V ~ 240V ~ BALANCING ELEMENT OUTPUT* 550W 820W 1100W STORAGE OUTPUT 1742W 2613W 3484W CHARGE PERIOD... - Page 16 WARNING: In order to avoid overheating do not cover the heater. The symbol on the product or in its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.