Related Manuals for Clarke STRONG-ARM CSA12F
Summary of Contents for Clarke STRONG-ARM CSA12F
- Page 1 WARNING: Read these instructions before using the machine 12 TONNE HYDRAULIC PRESS MODEL NO: CSA12F PART NO: 7613015 OPERATION & MAINTENANCE INSTRUCTIONS GC0313...
-
Page 2: Safety Precautions
GUARANTEE This CLARKE product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt as proof of purchase. - Page 3 • Never tamper with the press. The safety valve is calibrated and sealed at the factory; do not attempt to change the setting. • Use only the recommended hydraulic oil. • Components of this press are specially designed to withstand the rated capacity.
- Page 4 Ensure the press and its components suffered no damage during transit and that all components are present. Should any loss or damage become apparent, please contact your CLARKE dealer immediately. IMPORTANT: Due to the weight of the press components, we recommend that you get assistance during assembly.
- Page 5 7. With the upper ring already screwed home onto the ram body as supplied, lower the ram through the hole in the base plate and secure in position using the locking collar. 8. Insert the bed support pins into the holes in the side support at a height of your choosing.
- Page 6 12. Unscrew the filler plug on the end of the cylinder and remove the dipstick to check that the pump is filled with oil up to the raised mark the dipstick. 13. Attach the pump support plate to the right-hand side support using the fixing bolts, nuts and washers, ensuring it is level before tightening the bolts.
- Page 7 POSITIONING THE BED IMPORTANT: Due to the weight of the bed, we recommend that you get assistance from another person when adjusting the bed height. 1. Position the bed at the desired height, so that it will be as close as possible to the ram when the workpiece is mounted on it.
-
Page 8: Operation
If one of the mandrells is required, the adaptor must be fitted instead of the pressure cap. Secure the adaptor by tightening the grub screw with a suitable hex key as previous. Select your mandrell depending upon the size of the workpiece bearing surface. -
Page 9: Maintenance
It is recommended that a thorough annual inspection of the press be made and that any defective parts be replaced with genuine Clarke parts. • Any press which appears to be damaged in any way, is found to be badly worn, or operates abnormally SHOULD BE REMOVED FROM SERVICE until the necessary repairs are made. -
Page 10: Troubleshooting
Oil should be level with the bottom of the hole. If necessary top up with CLARKE hydraulic oil, Part No. 3050830. This task is carried out with the ram fully retracted. -
Page 11: Technical Specifications
TECHNICAL SPECIFICATIONS Capacity 12 Tonne Dimensions Operating Pressure 10000 PSI A 80 mm 695 mm (ex pump) Ram Stroke 184 mm 515 mm G 500 mm Ram Diameter 42 mm C 945 mm 1662 mm Net Weight 85 kg D 205 mm 152 mm 185 mm Parts &... -
Page 12: Frame Assembly Parts Diagram
FRAME ASSEMBLY PARTS DIAGRAM Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... - Page 13 PARTS LISTS PART NO DESCRIPTION PART NO DESCRIPTION Pressure Gauge Bolt M10 x 30 Nylon Washer Washer 10mm Ram Assembly Spring Washer 10mm Upper Collar M10 Nut Ram Base Plate Bolt M10 x 25 Lower Collar Pump Assembly Hydraulic Hose Bolt M6 x 16 Hex Hd Cross beam Washer 6mm...
-
Page 14: Ram Parts Diagram
RAM PARTS DIAGRAM Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... -
Page 15: Declaration Of Conformity
DECLARATION OF CONFORMITY Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...