Table of Contents
Advertisement
Quick Links
Please direct all questions to your local VeEX Sales Office, Representative, or Distributor. Or, contact VeEX technical support at
www.veexinc.com. Copyright 2014 VeEX Incorporated. All rights reserved.
No part of this user manual may be reproduced, translated into a foreign language, or be transmitted electronically without prior
agreement and written consent of VeEX Incorporated as governed by International copyright laws. Information contained in this
manual is provided "as is" and is subject to change without notice. Trademarks of VeEX Incorporated have been identified where
applicable, however the absence of such identification does not affect the legal status of any trademark.
Page 1 of 14
CX380X
Advanced Spectrum and Burst QAM Analyzer
Hardware Installation Guide
CX380X Hardware Installation Guide D07-00-077P Rev. A00
USER MANUAL
Advertisement
Table of Contents
Related Manuals for VeEX CX380X
Summary of Contents for VeEX CX380X
- Page 1 VeEX Incorporated as governed by International copyright laws. Information contained in this manual is provided “as is” and is subject to change without notice. Trademarks of VeEX Incorporated have been identified where applicable, however the absence of such identification does not affect the legal status of any trademark.
-
Page 2: Table Of Contents
4.3.3 Grounding ..................... 8 4.4 safety Guidelines ......................8 5.0 insTAllATion ....................9 5.1 installing the CX380X in a rack ..................9 5.2 Connecting Communications serial Ports ..............10 5.3 Connecting ethernet Control Ports................10 5.4 Connecting the rf Ports ....................10 5.3 Connecting the Power .................... -
Page 3: About This Guide
VeEX Inc. The software is protected by copyright and contains trade secrets of VeEX Inc or VeEX’s licensors. The purchaser of this device agrees that it has received a license solely to use the software as embedded in the device, and the purchaser is prohibited from copying, reverse engineering, decom- piling, or disassembling the software. -
Page 4: Introduction
CX380X can be added to VeEX CX380X probes network or can be used as a standalone solution to extend its capabilities for advanced forward path monitoring, troubleshooting and auditing the performance of analog and digital channels being transmitted downstream across CATV HFC network. -
Page 5: Safety Information
Do not operate the instrument in the presence of flammable gases or fumes or any other combustible environment. VeEX Inc. assumes no liability for the customer’s failure to comply with safety precautions and requirements. safety symbols This section includes warning symbols that appear in this manual. -
Page 6: Getting Started
The following items are included in the box: USB/Serial Port Adaptor Rack Mounting Brackets AC Power Adaptor Power Cord Two pairs of RS232 male-to-female DB-9 to DB-9 straight cables Page 6 of 14 CX380X Hardware Installation Guide D07-00-077P Rev. A00... -
Page 7: Tools Required
4.2 Tools required Phillips Screwdriver 4.3 Product features and Characteristics 4.3.1 front Panel The front panel of the CX380X contains status LED. 4.3.2 rear Panel dC 15V: 15 V DC input PoWer: Power On/Off switch rs232C db9 Console A/b: Console port for initial and basic configuration rs232C db9 switch Ctrl A/b (male): Control port from CPU board. -
Page 8: Grounding
Chassis lifting Guidelines A fully configured CX380X weighs approximately 11 pounds (5 Kilograms). The chassis is not intended to be moved frequently. Before you install the CX380X, plan chassis placement and ensure that your site is properly prepared so you can avoid having to move the chassis later to accommodate power sources and network con- nections. -
Page 9: Installation
Use the supplied serial cables to connect DB9 Switch Ctrl A port to the DB9 Switch Control In A port; repeat for B ports Connect the RJ-45 Control A/B ports to the LAN after the IP addresses of the CX380X is config- ured When installing equipment, ensure adequate ventilation is available. -
Page 10: Connecting Communications Serial Ports
When connecting the RF input ports to the HFC network, take note of the following: When connecting the F-connector on the cable to the RF connector on the CX380X chassis, always use a torque wrench to set the tightness to 15 inch- lbs. Do not simply hand-tighten the F-connectors. F-connectors that are too loose can cause RF leakage. -
Page 11: Connecting The Power
2. Unplug the power plug from the DC 15V power receptacle. 5.5 starting the system After installing the CX380X and connecting the required cables, please configure the IP address of the system to match the specific operation needs. Page 11 of 14... -
Page 12: Power Consumption
6.0 PoWer ConsumPTion The following is a statement from VeEX on the power consumption of its Monitoring Devices: CX180F -10x4 – 110V AC or 48V DC – consumes 20W per probe. CX380X – 110V AC– consumes 40W per probe. Please note that 110V and 48V are available but are mutually exclusive. -
Page 13: Warranty And Software
Replace hardware that proves to be defective provided that the products that the customer elects to replace is returned to VeEX Inc by the customer, along with proof of purchase, within thirty (30) days of the request by the customer, freight prepaid. -
Page 14: About Veex
8.0 AbouT VeeX VeEX Inc, the Verification EXperts, is an innovative designer and manufacturer of test and measurement solu- tions addressing numerous technologies. Global presence through a worldwide distribution channel provides uncompromised product support. Visit us online at www.veexinc.com for latest updates and additional documentation. VeEX Incorporated 2827 Lakeview Court Fremont, CA 94538.
Need help?
Do you have a question about the CX380X and is the answer not in the manual?
Questions and answers