Related Manuals for Nordson Auto-Flo RT Gun
Summary of Contents for Nordson Auto-Flo RT Gun
- Page 1 Auto-Flo RT Gun Customer Product Manual Part 1074874A--02 Issued 10/08 NORDSON CORPORATION • AMHERST, OHIO • USA...
-
Page 2: Table Of Contents
555 Jackson Street Amherst, OH 44001 Notice This is a Nordson Corporation publication which is protected by copyright. Original copyright date 2006. No part of this document may be photocopied, reproduced, or translated to another language without the prior written consent of Nordson Corporation. The information contained in this publication is subject to change without notice. -
Page 3: Safety
Make sure the spray area is adequately ventilated. Intended Use To prevent injury, be aware of less-obvious dangers Use of Nordson equipment in ways other than those in the workplace that often cannot be completely described in the documentation supplied with the... -
Page 4: Fire Safety
Use only replacement parts that are designed for use Injection in the skin is a serious traumatic injury. It is with original equipment. Contact your Nordson important to treat the injury surgically as soon as representative for parts information and advice. -
Page 5: Description
Auto-Flo RT Gun Description See Figure 1. The Auto-Flo RT gun is designed for use as a material outlet valve on an SDS Meter. It can be wired for 120- and 240-volt circuits. The Auto-Flo RT gun can be configured with a QUISS RTVision sensor head to provide continuous monitoring of the material bead during the application process. -
Page 6: Installation
Auto-Flo RT Gun Installation Operation See Figure 3 and perform the applicable procedures. Operation of the Auto-Flo RT gun is dependent upon the system and application requirements. WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety... - Page 7 Auto-Flo RT Gun Figure 3 Installation Part 1074874A--02 E 2008 Nordson Corporation...
-
Page 8: Troubleshooting
Refer to the appropriate system manuals for more information if the Corrective Actions listed here do not Table 3 lists the consumable items that are required to solve the problem. repair the Auto-Flo RT gun. Table 3 Consumable Items Possible Problem... -
Page 9: Remove The Gun
3. Disconnect the gun cable (13) from the bulk unloader controller. 4. Only perform this step if using the Auto-Flo RT gun with a QUISS RTVision sensor head (5): a. Disconnect the QUISS RTVision system cables (4) from the sensor head (5). -
Page 10: Replace The Seal Cartridge
2-station connector (6). Tighten the 2-station connector screws. See Figure 3 and refer to the Install the Auto-Flo RT Gun onto the SDS Meter procedure to put the Auto-Flo RT 7. Apply Loctite 242 adhesive to the threads of the gun back into service. - Page 11 Auto-Flo RT Gun TYPICAL WIRE ROUTING ELECTRICAL BOX ONLY REMOVED FOR CLARITY. SCREW LOCATION 120 VOLT CIRCUIT 240 VOLT CIRCUIT HEATER HEATER HEATER HEATER WIRE 1 WIRE A TEMP. SENSOR TEMP. SENSOR WIRE 2 WIRE B WIRE 3 WIRE C...
-
Page 12: Parts
Auto-Flo RT Gun Parts Auto-Flo RT Gun See Figure 6 and refer to the following parts list. To order parts, call the Nordson Customer Service Center or your local Nordson representative. Figure 6 Parts Part 1074874A--02 E 2008 Nordson Corporation... - Page 13 Auto-Flo RT Gun Item Part Description Quantity Note — 1074307 Gun, Auto-Flo RT 1074308 S Cartridge, seal S Screw, socket, M5 x 60 982171 900464 S Loctite 242, 50 ml 971521 S Elbow, male, tube x 1062768 S Heater, 120 Vac, 25 watt...
-
Page 14: Seal Kit
Auto-Flo RT Gun Seal Kit See Figure 7. The following seal kit is available for the Auto-Flo RT gun. This kit includes instructions for replacing the cartridge seals. Figure 7 Seal Kit Item Part Description Quantity Note — 1074446 Kit, seal - - - - - - S O-ring, Viton, 1.428 x 0.070...