Related Manuals for Teknik 5418072
Summary of Contents for Teknik 5418072
- Page 1 Teknik www.teknikoffice.co.uk For all your newfangled gadgetry. Shaker Style Desk 5418072 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
- Page 2 Table of Contents Assembly Tools Required Part Identifi cation No. 2 Phillips Screwdriver Tip Shown Actual Size Hardware Identifi cation Assembly Steps 5-22 Hammer Not actual size Skip the power trip. This time. Part Identifi cation RIGHT END (1) BOTTOM (2) RIGHT MIDDLE REAR LEG (1) LEFT END (1) OUTER BOTTOM (4)
- Page 3 Now you know Part Identifi cation our ABCs. å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identifi cation to help identify similar parts. D151 D953 D151...
- Page 4 Hardware Identifi cation å Screws are shown actual size. You may receive extra hardware with your unit. FILE GLIDE - 2 EXTENSION RAIL - 4 EXTENSION SLIDE - 4 FILE ROD - 2 (EXTENSION SET SHOWN SEPARATED) HIDDEN CAM - 72 CAM DOWEL - 28 CAM SCREW - 44 12F TWIST-LOCK...
- Page 5 Step 1 Assemble your unit on a carpeted fl oor or on the empty å carton to avoid scratching your unit or the fl oor. To begin assembly, push a WIST-LOCK® å FASTENER (12F) into the large holes in the LARGE BACK (H). Do not tighten the TWIST-LOCK®...
- Page 6 Step 2 Push seventy-two HIDDEN CAMS (1F) into å the ENDS (A and B), UPRIGHTS (C Arrow and D), BOTTOMS (F and G), BACKS (H and I), and MOLDINGS (S and T). Then, insert the metal end of a CAM DOWEL (2F) into each HIDDEN CAM, except in the short edges of the ENDS (A and B), short edges of the UPRIGHTS (C...
- Page 7 Step 3 Turn forty-four CAM SCREWS (8F) into the LEGS (K, L, M, å N, O, and P). (44 used) Page 7...
- Page 8 Step 4 Turn four BLACK 9/16" FLAT HEAD SCREWS (32S) into å the ENDS (A and B) until the shoulders of the SCREWS Some assembly rest on the surfaces of the ENDS. (and snacks) required. Slide the END MOLDINGS (U) onto the ENDS (A and B). å...
- Page 9 Step 5 Flip the ENDS (A and B) over. å Fasten the LEGS (K and M) and a BOTTOM SIDE å MOLDING (T) to the RIGHT END (A). Tighten six HIDDEN CAMS. Fasten the LEGS (L and N) and a BOTTOM SIDE å...
- Page 10 Step 6 Fasten the LEGS (L and O) and a BOTTOM SIDE å MOLDING (T) to the UPRIGHT (C). Tighten six HIDDEN CAMS. Fasten the LEGS (K and P) and a BOTTOM SIDE å MOLDING (T) to the LEFT UPRIGHT (D). Tighten six HIDDEN CAMS.
- Page 11 Step 7 Separate the EXTENSION SLIDES (W) from the EXTENSION RAILS (V) as shown in the enlarged diagram below. Be å prepared, the parts are greasy. Fasten the EXTENSION RAILS (V) to the ENDS (A and B) and UPRIGHTS (C and D). Use eight GOLD 5/16" FLAT å...
- Page 12 Step 8 Insert a WOOD DOWEL (15F) into each short edge of å a BOTTOM (F). Lay two OUTER BOTTOMS (G) next to the BOTTOM (F) å as shown. Fasten two BOTTOM MOLDINGS (S) to the BOTTOMS (F å and G). Tighten six HIDDEN CAMS. NOTE: Be sure the WOOD DOWELS insert into the å...
- Page 13 Step 9 Fasten the MIDDLE REAR LEGS (O and P) to the LARGE å BACK (H). Tighten four HIDDEN CAMS. Maximum Arrow 210 degrees Fasten the BRACE (J) to the MIDDLE REAR LEGS (O and P). å Use four BLACK 2" PAN HEAD SCREWS (66S). Minimum 190 degrees Edge with...
- Page 14 Step 10 Fasten the SMALL BACKS (I) to the MIDDLE REAR å LEGS (O and P). Tighten four HIDDEN CAMS. Finished edge Finished edge Page 14...
- Page 15 Step 11 Fasten a BOTTOM assembly to the LEGS (L and O) å and BOTTOM SIDE MOLDING (T). Tighten four Maximum Arrow 210 degrees HIDDEN CAMS. Fasten the remaining BOTTOM assembly to the LEGS (K å Minimum and P) and BOTTOM SIDE MOLDING (T). Tighten four 190 degrees HIDDEN CAMS.
- Page 16 Step 12 Fasten the LEFT END ASSEMBLY to the SMALL BACK (I) and å BOTTOM ASSEMBLY on the left end of your unit. Tighten six Now might be a HIDDEN CAMS. good time to refresh your drink. Fasten the RIGHT END ASSEMBLY to the SMALL BACK (I) and å...
- Page 17 Step 13 Carefully stand your unit upright. å ® How to use the TWIST-LOCK FASTENER Fasten the TOP (E) to the ENDS (A and B) and 1. Insert the dowel end of the FASTENER into the hole of the å adjoining part.
- Page 18 Step 14 Fasten three METAL BRACKETS (4G) to the TOP å MOLDING (R). Use three BLACK 9/16" LARGE HEAD SCREWS (1S). NOTE: Be sure the BRACKETS are even with the edges å of the MOLDING. Fasten the TOP MOLDING (R) to the TOP (E). Use three å...
- Page 19 Step 15 Tap down with your screwdriver and hammer. BLACK 9/16" LARGE HEAD SCREW (8 used in this step) Pull the DRAWER FRONT BRACKETS (10G) apart and slide them into the grooves in the DRAWER SIDES (D48 and D49). You may å...
- Page 20 Step 16 Fasten the EXTENSION SLIDES (W) to the DRAWER å SIDES (D48 and D49). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. Fasten a KNOB SET (100K) to the DRAWER FRONT (Q). å Use a SILVER 1/2" MACHINE SCREW (38S). Repeat this step for the other drawer.
- Page 21 Step 17 Push a FILE GLIDE (4B) onto the DRAWER RIGHT SIDE (D48). å Slide the FILE RODS (7B) into the FILE GLIDE (4B) on the Almost time to å DRAWER RIGHT SIDE (D48). celebrate! With a nap. Slide another FILE GLIDE (4B) onto the other end of the å...
- Page 22 Step 18 To insert the drawers into your unit, line up the å EXTENSION SLIDES on the drawer with the EXTENSION RAILS on the unit and push the drawer into the unit until the drawer is fully inserted. The drawers will push in hard until it is all the way in, then it will slide in and out easier.
- Page 23 WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves and drawers. •...