Related Manuals for Teknik Barrister Home
Summary of Contents for Teknik Barrister Home
- Page 1 Teknik www.teknikoffice.co.uk Your centre of attention. Barrister Home Sideboard Barrister Home Collection | Model 5416488 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
- Page 2 Table of Contents Assembly Tools Required Part Identifi cation No. 2 Phillips Screwdriver Tip Shown Actual Size Hardware Identifi cation Assembly Steps 6-20 Hammer Not actual size Français 21-24 Español 25-28 Skip the power trip. Safety 29-30 This time. Warranty WARNING Use of a TV that is too heavy or large is hazardous.
-
Page 3: Part Identification
Now you know Part Identifi cation our ABCs. å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identifi cation to help identify similar parts. RIGHT END (1) BACK (1) TOP MOLDING (1) -
Page 4: Hardware Identification
Hardware Identifi cation å Screws are shown actual size. You may receive extra hardware with your unit. HIDDEN CAM - 30 CAM DOWEL - 30 METAL BRACKET - 9 FOOT - 2 CORNER SMALL MAGNETIC 27H HINGE - 4 STRIKE PLATE - 2 CATCH - 1 BRACKET - 2 DECORATIVE... - Page 5 Hardware Identifi cation å Screws are shown actual size. You may receive extra hardware with your unit. BLACK 9/16" LARGE HEAD SCREW - 46 BLACK 1-7/8" FLAT HEAD SCREW - 4 BLACK 1/2" FLAT HEAD SCREW - 2 SILVER 3/4" MACHINE SCREW - 2 BLACK 9/16"...
- Page 6 Step 1 Assemble your unit on a carpeted fl oor or on the empty å carton to avoid scratching your unit or the fl oor. Push thirty HIDDEN CAMS (1F) into the ENDS (A å and B), UPRIGHTS (C and D), TOP (E2), BOTTOM (F), and CATCH BRACE (Q).
- Page 7 Step Step 2 Fasten the END MOLDINGS (P) to the ENDS (A and B) å and UPRIGHTS (C and D). Tighten twelve HIDDEN CAMS. These holes should be located here. These holes should be located here. Caution Start Tighten Risk of damage or Arrow injury.
- Page 8 Step 3 Fasten the METAL BRACKETS (4G) to the UPRIGHTS (C and D), å BOTTOM (F), and TOP MOLDING (M). Use nine BLACK 9/16" Remember: LARGE HEAD SCREWS (1S). Righty tighty. Lefty loosey. NOTE: The METAL BRACKETS should hang over the edges å...
- Page 9 Step Step 4 Fasten the LEFT END (B) and STOP MOLDING (R) to the å TOP (E2). Tighten six HIDDEN CAMS. Maximum Arrow 210 degrees Caution Minimum 190 degrees Do not stand the unit upright without the BACK fastened. The unit may collapse. Finished surface i t h f a c...
- Page 10 Step Step 5 Fasten the UPRIGHTS (C and D) to the TOP (E2). Tighten å four HIDDEN CAMS. Maximum Arrow 210 degrees Minimum 190 degrees i t h f a c S u r D E N H I D i t h o f a c S u r...
- Page 11 Step Step 6 Fasten the BOTTOM (F) to the LEFT END (B). Tighten two å HIDDEN CAMS. Maximum Arrow 210 degrees Fasten the CORNER BRACKET (31G) on the BOTTOM (F) å to the LEFT END (B). Use two BLACK 9/16" LARGE HEAD Minimum SCREWS (1S) through the CORNER BRACKET and into 190 degrees...
- Page 12 Step Step 7 Fasten the RIGHT END (A) to the TOP (E2). Tighten two å HIDDEN CAMS. Maximum Arrow 210 degrees Fasten the RIGHT END (A) to the BOTTOM (F). Tighten two å HIDDEN CAMS. Minimum Fasten the CORNER BRACKET (31G) on the BOTTOM (F) 190 degrees å...
- Page 13 Step Step 8 Fasten the TOP MOLDING (M) to the TOP (E2). Use four å BLACK 9/16" LARGE HEAD SCREWS (1S) through the Maximum Arrow BRACKETS and into the TOP. 210 degrees NOTE: To fasten the TOP MOLDING, you may need to å...
- Page 14 Step Step 9 Fasten the BASE (L) to the ENDS (A and B) and BOTTOM (F). å Use seven BLACK 9/16" LARGE HEAD SCREWS (1S) through Don't worry. It isn't the BRACKETS and into the BASE. Rome. This can be built in a day.
- Page 15 Step Step 10 Carefully turn your unit over onto its front edges. Unfold the å Caution BACK (G) and lay it over your unit. Do not stand the unit upright without the Make equal margins along all four edges of the BACK (G). Push å...
- Page 16 Step Step 11 IMPORTANT: You may need someone's help in this step. å Pro Tip: Lift with your Carefully stand your unit upright. å legs. And, you know, your arms. Push the SMALL MAGNETIC CATCH (2I) into the center hole in å...
- Page 17 Step Step 12 Fasten the HINGES (27H) to the DOORS (H and I). Use eight å BLACK 9/16" LARGE HEAD SCREWS (1S). NOTE: The HINGES should be positioned exactly as shown. å Position the HINGE exactly as shown. BLACK 9/16" LARGE HEAD SCREW (8 used in this step) Position the HINGE exactly as shown.
- Page 18 Step Step 13 Fasten the DOORS (H and I) to the END MOLDINGS (P) on the å UPRIGHTS (C and D). Use eight BLACK 9/16" LARGE HEAD SCREWS (1S). Fasten the DECORATIVE ENDS (33M) to the DOOR (H). Use two SILVER 3/4" å...
- Page 19 Step Step 14 Slide the SHELF MOLDINGS (N and O) onto the notched å edges of the ADJUSTABLE SHELVES (J and K). *U.S. Patent No. 5,499,886 å Notched edge Notched edge Notched edge Page 19...
- Page 20 Step Step 15 Apply the WARNING LABEL (3L) to the TOP (E2). You should be able to read the label when the TV is removed from the å unit. When the TV is in place, it should hide the label. Peel off the backing and apply the label as shown in the diagram. NOTE: This is a permanent label intended to last for the life of the product.
- Page 21 WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following safety information. Death or serious injury may occur when children climb on audio and/or video equipment furniture. A remote control or toys placed on the furnishing may encourage a child to climb on the furnishing and as a result may tip over onto the child.