Related Manuals for Teknik Canal Heights 5419231
Summary of Contents for Teknik Canal Heights 5419231
- Page 1 Teknik www.teknikoffice.co.uk Sit and surf. Canal Heights Console Desk 5419231 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
- Page 2 Table of Contents Assembly Tools Required Part Identifi cation No. 2 Phillips Screwdriver Tip Shown Actual Size Hardware Identifi cation Assembly Steps 5-23 Hammer Not actual size Skip the power trip. This time. Page 2...
- Page 3 Now you know Part Identifi cation our ABCs. å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identifi cation to help identify similar parts. END (2) FRONT LEFT PANEL (1) CROSS BRACE (2)
- Page 4 Hardware Identifi cation å Screws are shown actual size. You may receive extra hardware with your unit. EXTENSION SETS SHOWN SEPARATED EXTENSION RAIL - 2 EXTENSION SLIDE - 2 HIDDEN CAM - 25 CAM SCREW - 25 WOOD DOWEL - 43 HINGE - 2 KNOB - 1 BUMPER - 2...
- Page 5 Step 1 Assemble your unit on a carpeted fl oor or on the empty å carton to avoid scratching your unit or the fl oor. Turn thirteen CAM SCREWS (4) into the exact holes å shown in the TOP (D). (13 used) Page 5...
- Page 6 Step 2 Separate the EXTENSION SLIDES (2) from the å EXTENSION RAILS (1) as shown in the enlarged diagram below. Be prepared, the parts are greasy. Fasten the EXTENSION RAILS (1) to the UPRIGHTS (B å and C). Use six 1/2" PAN HEAD SCREWS (15). NOTE: Use the exact holes shown in the RAILS.
- Page 7 Step 3 Turn six CAM SCREWS (4) into the exact holes shown in å the REAR CORNERS (J and K) and BACK PANEL (F). Insert ten WOOD DOWELS (5) into the exact holes shown å in the REAR CORNERS (J and K) and BACK PANEL (F). (6 used) (10 used) Page 7...
- Page 8 Step 4 Insert two HIDDEN CAMS (3) into the BACK PANEL (F). å Fasten the BACK PANEL (F) to the CORNERS (J and K). å Tighten two HIDDEN CAMS. NOTE: Be sure the WOOD DOWELS in the edges of the å...
- Page 9 Step 5 Turn six CAM SCREWS (4) into the exact holes shown in the å FRONT PANELS (G and H) and FRONT CORNERS (I). Insert fourteen WOOD DOWELS (5) into the exact holes shown å in the FRONT PANELS (G and H) and FRONT CORNERS (I). (6 used) (14 used) Page 9...
- Page 10 Step 6 Insert two HIDDEN CAMS (3) into the FRONT PANELS (G and H). å Fasten the FRONT PANELS (G and H) to the FRONT å CORNERS (I). Tighten two HIDDEN CAMS. NOTE: Be sure the WOOD DOWELS in the edges of å...
- Page 11 Step 7 Insert four HIDDEN CAMS (3) into the ENDS (A) å and UPRIGHTS (B and C). Fasten the ENDS (A) and UPRIGHTS (B and C) to the å FRONT PANELS (G and H) and FRONT CORNERS (I). Tighten four HIDDEN CAMS. NOTE: Be sure the WOOD DOWELS in the edges of the å...
- Page 12 Step 8 Insert four HIDDEN CAMS (3) into the ENDS (A) å and UPRIGHTS (B and C). Fasten the ENDS (A) and UPRIGHTS (B and C) to the å BACK PANEL (F) and REAR CORNERS (J and K). Tighten four HIDDEN CAMS. NOTE: Be sure the WOOD DOWELS in the edges of the å...
- Page 13 Step 9 NOTE: You may need someone's help in this step. å Insert thirteen HIDDEN CAMS (3) into the ENDS (A), å UPRIGHTS (B and C), BACK PANEL (F), and FRONT PANELS (G and H). Fasten the TOP (D) to the ENDS (A), UPRIGHTS (B and C), å...
- Page 14 Step 10 Fasten the BOTTOM (E) to the ENDS (A), UPRIGHTS (B å and C), BACK PANEL (F), and FRONT PANELS (G and H). Use thirteen 1-1/2" FLAT HEAD SCREWS (9). NOTE: Be sure the WOOD DOWELS in the edges of the å...
- Page 15 Step 11 Fasten the LEG ASSEMBLIES (L and M) to the å BRACES (N). Use eight 1/2" MACHINE SCREWS (13). These holes must be here. 1/2" MACHINE SCREW (8 used in this step) These holes must be here. These holes must be here.
- Page 16 Step 12 Fasten the LEG ASSEMBLIES (L and M) and BRACES (N) å to the BOTTOM (E). Tighten ten 1-3/8" ALLEN BOLTS (10) using the ALLEN WRENCH (16). These holes must be here. 1-3/8" ALLEN BOLT (10 used in this step) The front of your unit Page 16...
- Page 17 Step 13 Fasten the CROSS BRACES (O) to the LEG ASSEMBLIES (L å and M). Use eight 1/2" MACHINE SCREWS (13). 1/2" MACHINE SCREW (8 used in this step) Page 17...
- Page 18 Step 14 Fasten the DRAWER SIDES (P and Q) to the DRAWER å BACK (S). Use two 1-1/2" FLAT HEAD SCREWS (9). 1-1/2" FLAT HEAD SCREW (2 used in this step) These holes must be here. Surface without holes Page 18...
- Page 19 Step 15 Insert three WOOD DOWELS (5) into the larger holes å in the edges of the DRAWER SIDES (P and Q) and DRAWER BACK (S). Fasten the DRAWER BOTTOM (T) to the DRAWER å SIDES (P and Q) and DRAWER BACK (S). Use six 1-1/2" FLAT HEAD SCREWS (9).
- Page 20 Step 16 Fasten the HINGES (6) to the DRAWER FRONT (R). Use å four 1/2" FLAT HEAD SCREWS (12). Fasten the KNOB (7) to the DRAWER FRONT (R). Use two å 3/4" MACHINE SCREWS (11). 1/2" FLAT HEAD SCREW (4 used in this step) 3/4"...
- Page 21 Step 17 Fasten the DRAWER FRONT (R) to the DRAWER å BOTTOM (T). Use two 9/16" LARGE HEAD SCREWS (14). Peel the paper backing from the BUMPERS (8) and stick å the BUMPERS onto the edges of the DRAWER SIDES (P and Q) where they come into contact with the DRAWER FRONT (R).
- Page 22 Step 18 Fasten the EXTENSION SLIDES (2) to the DRAWER å SIDES (P and Q). Use six 1/2" PAN HEAD SCREWS (15). NOTE: Use the exact holes shown in the SLIDES. å Open end Mounting holes Open end 1/2" PAN HEAD SCREW (6 used in this step) Open end Page 22...
- Page 23 Step 19 Carefully stand your unit upright. å To insert the drawer into your unit, line up the EXTENSION SLIDES on the drawer with the å EXTENSION RAILS on the unit and push the drawer into the unit until the drawer is fully inserted.
- Page 24 WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves and drawers. •...